Multi-Response Optimization of Turning Parameters with Vikor-Entropy Method on Machining of AA6061-TiB2 In-Situ Composites

Open Access

Year : | Volume : 11 | : | Page : –
By

    S. Chandra Sekhar

  1. K S B S V Sastry

  2. G.Murali

  3. Lalithya Karuturi

  1. Assistant Professor, Department of Mechanical Engineering, Sri Vasavi Engineering College, Andhra Pradesh, India
  2. Assistant Professor, Department of Mechanical Engineering, Sri Vasavi Engineering College, Andhra Pradesh, India
  3. Professor, Department of Mechanical Engineering, Koneru Lakshmaiah education and foundation, Andhra Pradesh, India
  4. Assistant Professor, Department of Mechanical Engineering, Sri Vasavi Engineering College, Andhra Pradesh, India

Abstract

In the manufacturing and metal cutting industries, the quality of the surface and strength is essential in defining the surface finish; an excellent surface finish indicates excellent quality in the product. The influence of machining parameters speed, feed and depth of cut on responses like material removal rate, surface roughness and Power consumption on turning of AA6061-TiB2 composites is investigated using the VIKOR-ENTROPY method. The effects of changing parameters on AA6061-TiB2 in-situ composite produced by the halide salt reaction method are explored in this paper. Twenty-seven experimental runs are carried out based on an orthogonal array. Material removal is selected as a quantitative target, and surface roughness is chosen as a qualitative target. This paper also refers to the Multi-response parameter optimization of CNC turning, such as speed, feed, and depth of cut, to improve material removal rate while simultaneously minimizing surface roughness and power consumption in turning composite. In order to handle these disparate responses, a novel entropy-VIKOR approach is used. The entropy approach calculates each response’s weight, and VIKOR is employed to rank the different parameter values. The combination of 1200 rpm speed, 150 mm/min feed, and 0.6 mm depth of cut is the best setting for this technique to simultaneously minimize surface roughness, power consumption and increase material removal rate.

Keywords: In-situ composites, turning, entropy, vikor, optimization

How to cite this article: S. Chandra Sekhar, K S B S V Sastry, G.Murali, Lalithya Karuturi Multi-Response Optimization of Turning Parameters with Vikor-Entropy Method on Machining of AA6061-TiB2 In-Situ Composites jopc ; :-
How to cite this URL: S. Chandra Sekhar, K S B S V Sastry, G.Murali, Lalithya Karuturi Multi-Response Optimization of Turning Parameters with Vikor-Entropy Method on Machining of AA6061-TiB2 In-Situ Composites jopc {cited };:-. Available from: https://journals.stmjournals.com/jopc/article=/view=131663

Full Text PDF Download

References

S. Chandrasekhar and N. B. V. Prasad, “Experimental Parametric Investigation of Electrochemical Drilling of AA6061- In Situ Composites,” J. Inst. Eng. Ser. C, vol. 100, no. 5, pp. 771–778, 2019, doi: 10.1007/s40032-019-00529-7.
G. Murali, M. Murugan, K. Arunkumar, P. V. Elumalai, D. Mohanraj, and S. Prabhakar. “Investigation and Process Parameter Optimization on Wire Electric Discharge Machining of Aluminium 6082 Alloy.” Advances in Materials Science and Engineering 2022.
S. Chandrasekhar and N. B. V. Prasad, “Experimental investigation on mechanical, wear and corrosive properties of Aa6061-in-situ composites produced by K2tif6-Kbf4reaction system at optimum holding time,” AIP Conf. Proc., vol. 2327, no. February, 2021, doi: 10.1063/5.0039805.
A. Mahamani, A. Jayasree, K. Mounika, K. R. Prasad, and N. Sakthivelan, “Evaluation of mechanical properties of AA6061-/ZrB2 in-situ metal matrix composites fabricated by K2TiF6-KBF4-K2ZrF6 reaction system,” Int. J. Microstruct. Mater. Prop., vol. 10, no. 3–4, pp. 185–200, 2015, doi: 10.1504/IJMMP.2015.072915.
D. K. Das, P. C. Mishra, S. Singh, and R. K. Thakur, “Properties of ceramic-reinforced aluminium matrix composites- A review,” Int. J. Mech. Mater. Eng., vol. 9, no. 1, pp. 1–16, 2014, doi: 10.1186/s40712-014-0012-9.
J. Paulo Davim, “Machining of metal matrix composites,” Mach. Met. Matrix Compos., pp. 1–162, 2012, doi: 10.1007/978-0-85729-938-3.
J. D. James Dhilip, J. Jeevan, D. Arulkirubakaran, and M. Ramesh, “Investigation and optimization of parameters for hard turning of OHNS steel,” Mater. Manuf. Process., vol. 35, no. 10, pp. 1113–1119, 2020, doi: 10.1080/10426914.2020.1765254.
K. Ramesh, S. Prathap Singh, K. Gnanasekaran, and A. S. Kumar, “Optimization of turning process parameters in machining of heat treated ductile iron bar using Taguchi technique,” Mater. Today Proc., vol. 22, pp. 2316–2323, 2019, doi: 10.1016/j.matpr.2020.03.353.
R. Viswanathan, S. Ramesh, S. Maniraj, and V. Subburam, “Measurement and multi-response optimization of turning parameters for magnesium alloy using hybrid combination of Taguchi-GRA-PCA technique,” Meas. J. Int. Meas. Confed., vol. 159, p. 107800, 2020, doi: 10.1016/j.measurement.2020.107800.
N. Tomac, K. Tonnessen, and F. O. Rasch, “Formation of Flank Build-up in Cutting Magnesium Alloys,” CIRP Ann. – Manuf. Technol., vol. 40, no. 1, pp. 79–82, 1991, doi: 10.1016/S0007-8506(07)61938-6.
C. Sivakandhan, G. Murali, N. Tamiloli, and L. Ravikumar. “Studies on mechanical properties of sisal and jute fiber hybrid sandwich composite,” Materials Today: Proceedings, 404 – 407, 2202.
D.C.L. Ravikumar, and C. S. G. Murali. Review on tribological performance of natural fibre-reinforced polymer composites,” J. Bio-Tribo-Corrosion 2018.
S. Dinesh, V. Senthilkumar, P. Asokan, and D. Arulkirubakaran, “Effect of cryogenic cooling on machinability and surface quality of bio-degradable ZK60 Mg alloy,” Mater. Des., vol. 87, pp. 1030–1036, 2015, doi: 10.1016/j.matdes.2015.08.099.
S. D. Pohekar and M. Ramachandran, “Application of multi-criteria decision making to sustainable energy planning – A review,” Renew. Sustain. Energy Rev., vol. 8, no. 4, pp. 365–381, 2004, doi: 10.1016/j.rser.2003.12.007.
S. Chandrasekhar and N. B. V. Prasad, “Electrochemical drilling and multi response optimization using different methods of assigning weights to the responses for sustainable machining of AA6061- in-situ composites,” Songklanakarin J. Sci. Technol., vol. 43, no. 6, pp. 1563–1569, 2021, doi: 10.14456/sjst-psu.2021.204.
S. Rajesh, S. Rajakarunakaran, and R. Sudhkarapandian, “Optimization of the red mud-aluminum composite in the turning process by the Grey relational analysis with entropy,” J. Compos. Mater., vol. 48, no. 17, pp. 2097–2105, 2014, doi: 10.1177/0021998313494914.
K. Jangra, S. Grover, and A. Aggarwal, “Optimization of multi machining characteristics in WEDM of WC-5.3%Co composite using integrated approach of Taguchi, GRA and entropy method,” Front. Mech. Eng., vol. 7, no. 3, pp. 288–299, 2012, doi: 10.1007/s11465-012-0333-4.
T. Sibalija, S. Petronic, and D. Milovanovic, “Experimental optimization of nimonic 263 laser cutting using a particle swarm approach,” Metals (Basel)., vol. 9, no. 11, 2019, doi: 10.3390/met9111147.
S. Chandrasekhar and N. B. V. Prasad, “Multi-response optimization of electrochemical machining parameters in the micro-drilling of AA6061-in situ composites using the Entropy–VIKOR method,” Proc. Inst. Mech. Eng. Part B J. Eng. Manuf., vol. 234, no. 10, pp. 1311–1322, 2020, doi: 10.1177/0954405420911539.
M. S. Mohsen and B. A. Akash, “Evaluation of domestic solar water heating system in Jordan using analytic hierarchy process,” Energy Convers. Manag., vol. 38, no. 18, pp. 1815–1822, 1997, doi: 10.1016/S0196-8904(96)00115-X.
K. Arunkumar, R. Kanagaraj, and G. Murali. “Influence of AWJM parameters on surface quality of BSHC.” Materials and Manufacturing Processes, 2023.
J. R. San Cristóbal, “Multi-criteria decision-making in the selection of a renewable energy project in spain: The Vikor method,” Renew. Energy, vol. 36, no. 2, pp. 498–502, 2011, doi: 10.1016/j.renene.2010.07.031.
C. Sivakandhan et al., “Material characterization and unconventional machining on synthesized Niobium metal matrix,” Mater. Res. Express, vol. 7, no. 1, 2019, doi: 10.1088/2053-1591/ab624d.
N. Tamiloli, J. Venkatesan, G. Murali, Shyam Prasad Kodali, T. Sampath Kumar, and M. P. Arunkumar. “Optimization of end milling on Al–SiC-fly ash metal matrix composite using Topsis and fuzzy logic.” SN Applied Sciences 1, 2019, 1-15.
I. Kakaravada, A. Mahamani, and V. Pandurangadu, “Optimization of machining parameters using Entropy-VIKOR method in drilling of A356-/TiC in-situ composites,” IOP Conf. Ser. Mater. Sci. Eng., vol. 390, no. 1, 2018, doi: 10.1088/1757-899X/390/1/012099.
S. Chandrasekhar and N. B. V. Prasad, “Optimization of the electrochemical machining parameters in drilling of AA6O6I- in-situ composites produced by K2TiF6-KBF4 reaction system,” IOP Conf. Ser. Mater. Sci. Eng., vol. 390, no. 1, 2018, doi: 10.1088/1757-899X/390/1/012006.
A. Shemshadi, H. Shirazi, M. Toreihi, and M. J. Tarokh, “A fuzzy VIKOR method for supplier selection based on entropy measure for objective weighting,” Expert Syst. Appl., vol. 38, no. 10, pp. 12160–12167, 2011, doi: 10.1016/j.eswa.2011.03.027.
S. Musani and A. A. Jemain, “Ranking schools’ academic performance using a fuzzy VIKOR,” J. Phys. Conf. Ser., vol. 622, no. 1, 2015, doi: 10.1088/1742-6596/622/1/012036.


Open Access Original Research
Volume
Received October 19, 2023
Accepted November 21, 2023
Published