[{“box”:0,”content”:”
n
n
- n t
n
Toshit Jain
[/foreach]
n
n
n
- [foreach 286] [if 1175 not_equal=””]n t
- , , ,
n[/if 1175][/foreach]
n
Abstract
nZinc-based alloys are potential biodegradable implants and can replace Magnesium and Titaniumbased materials via engineering their biomechanical properties with Zinc. Implants, due to their intricate geometries are difficult to fabricate by conventional manufacturing techniques. Therefore, they are usually fabricated by Additive manufacturing and Powder metallurgy techniques. In the present work, Zinc, Magnesium, manganese and titanium are alloyed using powder metallurgy technique. Vickers micro-hardness, UTM, Zeiss microscopy and Corrosion testing using body fluid are used for evaluation of mechanical properties. MWCNT dip coating is used to enhance the biomechanical characteristics of the prepared samples. The compressive strength of Zinc alloy is increased significantly when Magnesium, titanium and manganese are added in to the Zn based matrix. The micro-hardness of prepared samples are in the acceptable range for bio-implant application. Dip coating of MWCNT on Zn-1Mg-.8Mn shows better deposition and body fluid corrosion results marks considered as potential engineered alloy for bio implants fabrication in place of Ti-based implants.
n
Keywords: Zinc-based Alloys, Biomechanical characterization, ball milling powder metallurgy, nanotube dip-coating
n[if 424 equals=”Regular Issue”][This article belongs to Journal of Polymer and Composites(jopc)]
n
n
n
n
n
nn
nn[if 992 equals=”Open Access”] Full Text PDF[else] nvar fieldValue = “[user_role]”;nif (fieldValue == ‘indexingbodies’) {n document.write(‘Full Text PDF‘);n }nelse if (fieldValue == ‘administrator’) { document.write(‘Full Text PDF‘); }nelse if (fieldValue == ‘jopc’) { document.write(‘Full Text PDF‘); }n else { document.write(‘ ‘); }n [/if 992] [if 379 not_equal=””]nn
Browse Figures
n
n
n[/if 379]n
References
n[if 1104 equals=””]n
1.Krystýnová M., Doležal P., Fintová S., Březina M., Zapletal J., and Wasserbauer, J. Preparation and characterization of zinc materials prepared by powder metallurgy, Metals, 7(10), 396 (2017).
2. Say Y., Guler O., and Dikici B., Carbon nanotube (CNT) reinforced magnesium matrix composites: The effect of CNT ratio on their mechanical properties and corrosion resistance, Materials Science and Engineering: A, 798, 139636 (2020).
3. Bains, P. S., Sidhu, S. S., and Payal, H. S., Fabrication and machining of metal matrix composites: a review. Materials and Manufacturing Processes, 31(5), 553–573 (2016).
4. Deckers, J. P., Shahzad, K., Cardon, L., Rombouts, M., Vleugels, J., and Kruth, J. P., Shaping ceramics through indirect selective laser sintering, Rapid Prototyping Journal (2016).
5. Chaudhary, M., Jain, T., and Jain, J. K., Advanced manufacturing techniques and advancements in biodegradable biomaterials, Materials Today: Proceedings, 47, 6686–6692 (2021).
6. Jain, T., Jain, J. K., and Saxena, K. K. Design and Comprehensive Study of Biodegradable Zinc–based Implants for Bio–medical Application, Advances in Materials and Processing Technologies, 1–18 (2021).
7. Bose, S., Robertson, S. F., and Bandyopadhyay, A., Surface modification of biomaterials and biomedical devices using additive manufacturing, Acta biomaterialia, 66, 6–22 (2018).
8. Bornapour, M., Muja, N., Shum-Tim, D., Cerruti, M., and Pekguleryuz, M., Biocompatibility and biodegradability of Mg–Sr alloys: The formation of Sr-substituted hydroxyapatite, Acta biomaterialia, 9(2), 5319–5330 (2013).
9. Březina, M., Minda, J., Doležal, P., Krystýnová, M., Fintová, S., Zapletal, J., and Ptáček, P., Characterization of powder metallurgy processed pure magnesium materials for biomedical applications. Metals, 7(11), 461 (2017).
10. Taniguchi, N., Fujibayashi, S., Takemoto, M., Sasaki, K., Otsuki, B., Nakamura, T. and Matsuda, S., Effect of pore size on bone ingrowth into porous titanium implants fabricated by additive manufacturing: an in vivo experiment, Materials Science and Engineering: C, 59, 690–701 (2016).
11. Hettich, G., Schierjott, R. A., Epple, M., Gbureck, U., Heinemann, S., Mozaffari-Jovein, H., and Grupp, T. M. Calcium phosphate bone graft substitutes with high mechanical load capacity and high degree of interconnecting porosity. Materials, 12(21), 3471 (2019).
12. Katarivas Levy, G., Goldman, J., and Aghion, E., The prospects of zinc as a structural material for biodegradable implants—a review paper, Metals, 7(10), 402 (2017).
13. Miranda, G., Araújo, A., Bartolomeu, F., Buciumeanu, M., Carvalho, O., Souza, J. C. M., and Henriques, B., Design of Ti6Al4V-HA composites produced by hot pressing for biomedical applications, Materials and Design, 108, 488–493 (2016).
14. Kubásek, J., Dvorský, D., Čapek, J., Pinc, J., and Vojtěch, D., Zn-Mg biodegradable composite: novel material with tailored mechanical and corrosion properties. Materials, 12(23), 3930 (2019).
15. Sharma, K., Kaushalyayan, K. S., and Shukla, M., Pull-out simulations of interfacial properties of amine functionalized multi-walled carbon nanotube epoxy composites. Computational Materials Science, 99, 232–241 (2015).
16. Shukla, M. K., and Sharma, K., Improvement in mechanical and thermal properties of epoxy hybrid composites by functionalized graphene and carbon-nanotubes. Materials Research Express, 6(12), 125323 (2019).
17. Singh, P. K., Sharma, K., Kumar, A., and Shukla, M., Effects of functionalization on the mechanical properties of multiwalled carbon nanotubes: A molecular dynamics approach. Journal of composite materials, 51(5), 671–680 (2017).
18. Suh, J. Y., and Bae, D. H., Mechanical properties of Fe-based composites reinforced with multi-walled carbon nanotubes, Materials Science and Engineering: A, 582, 321–325 (2013).
19. Asri, R. I. M., Harun, W. S. W., Samykano, M., Lah, N. A. C., Ghani, S. A. C., Tarlochan, F., and Raza, M. R., Corrosion and surface modification on biocompatible metals: A review, Materials Science and Engineering: C, 77, 1261–1274 (2017).
20. Choudhary, M., Jain, J. K., Jain, T., Agrawal, R., and Kumar, S., Biocompatibility Enhancement of Magnesium Alloys via Surface Modification Method: A Review, Recent Advances in Smart Manufacturing and Materials, 423–431 (2021).
nn[/if 1104][if 1104 not_equal=””]n
- [foreach 1102]n t
- [if 1106 equals=””], [/if 1106][if 1106 not_equal=””],[/if 1106]
n[/foreach]
n[/if 1104]
nn
nn[if 1114 equals=”Yes”]n
n[/if 1114]
n
n
n
Volume | 11 |
Issue | 07 |
Received | August 22, 2023 |
Accepted | September 11, 2023 |
Published | September 22, 2023 |
n
n
n
n
n[/foreach]
n[/if 1190] [if 1177 not_equal=””]n
n
n[/foreach]
n[/if 1177]
n
n
n
n function myFunction2() {n var x = document.getElementById(“browsefigure”);n if (x.style.display === “block”) {n x.style.display = “none”;n }n else { x.style.display = “Block”; }n }n document.querySelector(“.prevBtn”).addEventListener(“click”, () => {n changeSlides(-1);n });n document.querySelector(“.nextBtn”).addEventListener(“click”, () => {n changeSlides(1);n });n var slideIndex = 1;n showSlides(slideIndex);n function changeSlides(n) {n showSlides((slideIndex += n));n }n function currentSlide(n) {n showSlides((slideIndex = n));n }n function showSlides(n) {n var i;n var slides = document.getElementsByClassName(“Slide”);n var dots = document.getElementsByClassName(“Navdot”);n if (n > slides.length) { slideIndex = 1; }n if (n (item.style.display = “none”));n Array.from(dots).forEach(n item => (item.className = item.className.replace(” selected”, “”))n );n slides[slideIndex – 1].style.display = “block”;n dots[slideIndex – 1].className += ” selected”;n }n n function myfun() {n x = document.getElementById(“editor”);n y = document.getElementById(“down”);n z = document.getElementById(“up”);n if (x.style.display == “none”) {n x.style.display = “block”;n }n else {n x.style.display = “none”;n }n if (y.style.display == “none”) {n y.style.display = “block”;n }n else {n y.style.display = “none”;n }n if (z.style.display == “none”) {n z.style.display = “block”;n }n else {n z.style.display = “none”;n }n }n function myfun2() {n x = document.getElementById(“reviewer”);n y = document.getElementById(“down2”);n z = document.getElementById(“up2”);n if (x.style.display == “none”) {n x.style.display = “block”;n }n else {n x.style.display = “none”;n }n if (y.style.display == “none”) {n y.style.display = “block”;n }n else {n y.style.display = “none”;n }n if (z.style.display == “none”) {n z.style.display = “block”;n }n else {n z.style.display = “none”;n }n }n”}]