Performance Evaluation of Concrete with Binary and Ternary Blends of Fly Ash, Silica Fume, and Fiber Reinforcement

Year : 2025 | Volume : 15 | Issue : 03 | Page : 40 45
    By

    Neelesh Nagle,

  • Harsh Rathore,

Abstract

This study evaluates the effect of ground granulated blast furnace slag (GGBS) as a partial replacement for cement on the mechanical properties of concrete, focusing on compressive and split tensile strength. Concrete mixes were prepared with GGBS replacement levels of 0%, 25%, and 50% and subjected to different curing methods, including water curing, steam curing, and conceal curing. These curing methods were selected to investigate their impact on hydration, strength development, and long-term performance. The results indicate that incorporating 25% GGBS provides an optimal balance between strength and sustainability, offering improvements in durability and reduced environmental impact, whereas a 50% replacement reduces both compressive and tensile strength due to slower pozzolanic reactions and insufficient early-age strength. Among the curing methods, concealed curing exhibited the highest strength development due to enhanced hydration and internal moisture retention, which promotes the continued reaction of cementitious materials, while steam curing led to the lowest strength values, likely as a result of rapid moisture loss and limited hydration. The split tensile strength followed a similar trend, confirming the beneficial role of GGBS in enhancing bond strength and crack resistance through improved matrix density and reduced porosity. The study highlights the significance of appropriate curing techniques and optimal GGBS content in achieving durable and high-performance concrete, which is essential for modern construction practices. These findings contribute to the sustainable use of industrial by-products in construction while maintaining structural integrity, promoting eco-friendly construction materials, and encouraging the adoption of green building technologies in the civil engineering sector.

Keywords: GGBS, compressive strength, split tensile strength, curing methods, sustainable concrete, pozzolanic reaction, mechanical properties

[This article belongs to Journal of Construction Engineering, Technology & Management ]

How to cite this article:
Neelesh Nagle, Harsh Rathore. Performance Evaluation of Concrete with Binary and Ternary Blends of Fly Ash, Silica Fume, and Fiber Reinforcement. Journal of Construction Engineering, Technology & Management. 2025; 15(03):40-45.
How to cite this URL:
Neelesh Nagle, Harsh Rathore. Performance Evaluation of Concrete with Binary and Ternary Blends of Fly Ash, Silica Fume, and Fiber Reinforcement. Journal of Construction Engineering, Technology & Management. 2025; 15(03):40-45. Available from: https://journals.stmjournals.com/jocetm/article=2025/view=234957


References

  1. Abbass W, Khan MI, Mourad S. Evaluation of mechanical properties of steel fiber reinforced concrete with different strengths of concrete. Constr Build Mater. 2018;168:556–569. doi: 10.1016/j.conbuildmat.2018.02.164.
  2. AbdelAleem BH, Ismail MK, Hassan AAA. The combined effect of crumb rubber and synthetic fibers on impact resistance of self-consolidating concrete. Constr Build Mater. 2018;162:816–829. doi: 10.1016/j.conbuildmat.2017.12.077.
  3. Ahsan MB, Hossain Z. Supplemental use of rice husk ash (RHA) as a cementitious material in concrete industry. Constr Build Mater. 2018;178:1–9. doi: 10.1016/j.conbuildmat.2018.05.101.
  4. Alghamdi AA, Alharthi HA. Multiscale 3D finite-element modelling of the thermal conductivity of clay brick walls. Constr Build Mater. 2017;157:1–9. doi: 10.1016/j.conbuildmat.2017.09.081.
  5. Al-Tayeb MM, Ismail H, Dawoud O, Wafi SR, Al Daoor I. Ultimate failure resistance of concrete with partial replacements of sand by waste plastic of vehicles under impact load. Int J Sustain Built Environ. 2017;6:610–616. doi: 10.1016/j.ijsbe.2017.12.008.
  6. Bhogayata AC, Arora NK. Impact strength, permeability, and chemical resistance of concrete reinforced with metalized plastic waste fibers. Constr Build Mater. 2018;161:254–266. doi: 10.1016/j.conbuildmat.2017.11.135.
  7. Biswal S, Ramaswamy A. Finite element model updating of concrete structures based on imprecise probability. Mech Syst Signal Process. 2017;94:165–179. doi: 10.1016/j.ymssp.2017.02.042.
  8. Boulekbache B, Hamrat M, Chemrouk M, Amziane S. Flexural behaviour of steel fibre-reinforced concrete under cyclic loading. Constr Build Mater. 2016;126:253–262. doi: 10.1016/j.conbuildmat.
    2016.09.035.
  9. Demin W, Fukang H. Investigation for plastic damage constitutive models of the concrete material. Procedia Eng. 2017;210:71–78. doi: 10.1016/j.proeng.2017.11.050.
  10. George J, Kalyana Rama JS, Siva Kumar MVN, Vasan A. Behavior of plain concrete beam subjected to three point bending using concrete damaged plasticity (CDP) model. Mater Today Proc. 2017;4:9742–9746. doi: 10.1016/j.matpr.2017.06.259.
  11. Gonen T. Freezing-thawing and impact resistance of concretes containing waste crumb rubbers. Constr Build Mater. 2018;177:436–442. doi: 10.1016/j.conbuildmat.2018.05.105.
  12. Gupta T, Sharma RK, Chaudhary S. Impact resistance of concrete containing waste rubber fiber and silica fume. Int J Impact Eng. 2015;83:76–87. doi: 10.1016/j.ijimpeng.2015.05.002.
  13. Jin R, Chen Q, Soboyejo ABO. Non-linear and mixed regression models in predicting sustainable concrete strength. Constr Build Mater. 2018;170:142–152. doi: 10.1016/j.conbuildmat.2018.03.
    063.
  14. Khademi F, Jamal SM, Deshpande N, Londhe S. Predicting strength of recycled aggregate concrete using artificial neural network, adaptive neuro-fuzzy inference system and multiple linear regression. Int J Sustain Built Environ. 2016;5:355–369. doi: 10.1016/j.ijsbe.2016.09.003.
  15. Mohammadhosseini H, Abdul Awal ASM, Mohd Yatim JB. RETRACTED: The impact resistance and mechanical properties of concrete reinforced with waste polypropylene carpet fibres. Constr Build Mater. 2017;143:147–157. doi: 10.1016/j.conbuildmat.2017.03.109.
  16. Mohammadhosseini H, Tahir MM, Sam ARM. RETRACTED: The feasibility of improving impact resistance and strength properties of sustainable concrete composites by adding waste metalized plastic fibres. Constr Build Mater. 2018;169:223–236. doi: 10.1016/j.conbuildmat.2018.02.210.
  17. Saxena R, Siddique S, Gupta T, Sharma RK, Chaudhary S. Impact resistance and energy absorption capacity of concrete containing plastic waste. Constr Build Mater. 2018;176:415–421. doi: 10.1016/j.conbuildmat.2018.05.019.
  18. Siddique S, Shrivastava S, Chaudhary S, Gupta T. Strength and impact resistance properties of concrete containing fine bone china ceramic aggregate. Constr Build Mater. 2018;169:289–298. doi: 10.1016/j.conbuildmat.2018.02.213.
  19. Wang YH, Tang Q, Nie X. Comparative investigation on influences of concrete material constitutive models on structural behavior. Constr Build Mater. 2017;144:475–483. doi: 10.1016/j.
    conbuildmat.2017.03.174.
  20. Zhong R, Zong Z, Niu J, Liu Q, Zheng P. A multiscale finite element model validation method of composite cable-stayed bridge based on probability box theory. J Sound Vib. 2016;370:111–131. doi: 10.1016/j.jsv.2016.01.055.

 

Regular Issue Subscription Original Research
Volume 15
Issue 03
Received 05/04/2025
Accepted 15/05/2025
Published 16/05/2025
Publication Time 41 Days
91

Login


My IP

PlumX Metrics