Experimental Analysis of Cutting Forces Under Different Machining Parameters and Carbide Inserts During Turning of Hardened AISI 4340 Steel

Open Access

Year : 2023 | Volume : | : | Page : –
By

Ranjan Kumar,

Sumanta Jungli,

Somnath Das,

Arijit Mukherjee,

Soumya Ghosh,

  1. Scholar, Department of Mechanical Engineering, Swami Vivekananda University, Barrackpore,, West Bengal, India
  2. Assistant Professor, Assistant Professor, Department of Mechanical Engineering, Swami Vivekananda University, Barrackpore, West Bengal, India
  3. Assistant Professor, Department of Mechanical Engineering, Swami Vivekananda Institute of Science & Technology, Rajpur Sonarpur, Kolkata,, West Bengal, India
  4. Assistant Professor, Assistant Professor, Department of Mechanical Engineering, Swami Vivekananda University, Barrackpore, West Bengal, India
  5. Assistant Professor, Assistant Professor, Department of Mechanical Engineering, Swami Vivekananda University, Barrackpore, West Bengal, India

Abstract

Turning of hardened materials with an advanced coated carbide insert has numerous advantages over the grinding process, e.g., reduced process cost, high material removal rate, and less environmental concern due to the elimination of the cutting fluid. Process parameters in conventional machining operations like cutting speed, feed, and depth of cut play the most crucial role behind the generation
of heat which also leads to microstructural changes, improved tool life, better surface finish, metal removal rate, and the most important is cutting force. In the present work, turning has been done on hardened AISI 4340 steel (42 HRC) using three different inserts of coated carbide (Titanium carbide coated groove-type SNMG-120408-PM, TiC-coated plain SNMA-120408-315/K15 and Al2O3 coated
groove SNMG-120408-THM) under the dry condition with a constant depth of cut. The cutting force has been analyzed under the different cutting conditions, chip profile, chatter, built-up edge, and chip reduction coefficient (CRC). A comparative study has been presented among different tool inserts to get desired performance such as material removal rate, tool wear, and profile of chips. In comparison with Al2O3 coated carbide insert the groove-type TiC-coated carbide inserts have shown better
machining results at higher cutting velocity and feed rate while turning cylindrical workpiece. No built-up edge has formed at TiC-coated carbide insert but SNMG-120408-THM insert results in a built-up edge chip. TiC-coated groove-type (SNMG-120408-PM) insert has shown longer tool life than the other two tool insert used in this work. Favorable chip formation, that is flat continuous-type
chip, is obtained at TiC-coated groove-type insert and may be recommended.

Keywords: Carbide inserts, turning, cutting force, machinability, AISI 4340 SS, chip

How to cite this article:
Ranjan Kumar, Sumanta Jungli, Somnath Das, Arijit Mukherjee, Soumya Ghosh. Experimental Analysis of Cutting Forces Under Different Machining Parameters and Carbide Inserts During Turning of Hardened AISI 4340 Steel. Journal of Polymer and Composites. 2023; ():-.
How to cite this URL:
Ranjan Kumar, Sumanta Jungli, Somnath Das, Arijit Mukherjee, Soumya Ghosh. Experimental Analysis of Cutting Forces Under Different Machining Parameters and Carbide Inserts During Turning of Hardened AISI 4340 Steel. Journal of Polymer and Composites. 2023; ():-. Available from: https://journals.stmjournals.com/jopc/article=2023/view=95514


Full Text PDF

References

1. Han S, Melkote SN, Haluska MS, Watkins TR. White layer formation due to phase transformation in orthogonal machining of AISI 1045 annealed steel. Mater Sci Eng A. 2008; 488(1-2): 195–204. doi: 10.1016/j.msea.2007.11.081.
2. Uhlmann E, Stawiszynski B, Leyens C, Heinze S, Sammler F. Hard Turning of Hot Work and Cold Work Steels with HiPIMS and DCMS TiAlN Coated Carbide Inserts. Procedia CIRP. 2016; 46: 591–4. doi: 10.1016/j.procir.2016.03.231.
3. Yallese MA, Chaoui K, Zeghib N, Boulanouar L, Rigal J. Hard machining of hardened bearing steel using cubic boron nitride tool. J Mater Process Technol. 2009; 209(2): 1092–104. doi: 10.1016/j.jmatprotec.2008.03.014.
4. Huang Y, Liang SY. Modeling of cutting forces under hard turning conditions considering tool wear effect. Transactions of the ASME. J Manuf Sci Eng. 2005; 127(2): 262–70. doi: 10.1115/1.1852571.
5. Zhou JM, Andersson M, Stahl JE. The monitoring of flank wear on the CBN tool in the hard turning process. Int J Adv Manuf Technol. 2003; 22(9-10): 697–702. doi: 10.1007/s00170-003-1569-2.
6. Nayak M, Sehgal R. Effect of Tool Material Properties and Cutting Conditions on Machinability of AISI D6 Steel During Hard Turning. Arab J Sci Eng. 2015; 40(4): 1151–64. doi: 10.1007/s13369-015-1578-0.
7. Guo YB, Warren AW, Hashimoto F. The basic relationships between residual stress, white layer, and fatigue life of hard turned and ground surfaces in rolling contact. CRIP J Manuf Sci Technol. 2010; 2(2): 129–34. doi: 10.1016/j.cirpj.2009.12.002.
8. Ciftci I. Machining of austenitic stainless steels using CVD multi-layer coated cemented carbide tools. Tribol Int. 2006; 39(6): 565–9. doi: 10.1016/j.triboint.2005.05.005.
9. Schwach DW, Guo YB. Feasibility of producing optimal surface integrity by process design in hard turning. Mater Sci Eng. 2005; 395(1-2): 116–23. doi: 10.1016/j.msea.2004.12.012.
10. Sahoo AK, Sahoo B. Experimental investigations on machinability aspects in finish hard turning of AISI 4340 steel using uncoated and multilayer coated carbide inserts. Measurement. 2012; 45(8): 2153–65. doi: 10.1016/j.measurement.2012.05.015.
11. Chattopadhyay AB. Machining and Machine Tools. New Delhi: Wiley India Pvt Ltd; 2013.
12. Javidi A, Rieger U, Eichlseder W. The Effect of Machining on the Surface Integrity and fatigue Life. Int J Fatugue. 2008; 30(10-11): 2050–5. doi: 10.1016/j.ijfatigue.2008.01.005.
13. Mondal K, Das S. An investigation on machinability during turning hardened steel in dry condition. J Inst Eng (India) S C. 2018; 99(6): 637–44. doi: 10.1007/s40032-017-0370-1.


Open Access Original Research
Volume
Received 27/08/2022
Accepted 25/11/2022
Published 19/01/2023