Devesh Ojha,
Vivek Verma,
Anuradha Misra,
- Assistant Professor, Department of Civil Engineering, Amity University, Lucknow, India Campus: Amity University, Lucknow, Uttar Pradesh, India
- Assistant Professor, Department of Mechanical Engineering, Amity University, Lucknow, India Campus: Amity University, Lucknow, Uttar Pradesh, India
- Assistant Professor, Department of Computer Science & Engineering, Amity University, Lucknow, Uttar Pradesh, India
Abstract
Acoustic metamaterials for sound insulation and photonic/radiative-cooling metamaterials for passive thermal management have each matured separately for building-envelope retrofit, but existing studies address ventilation, acoustic damping and radiative thermal control in isolation, and no reported unit-cell architecture co-designs all three within a single shared structure. This gap persists because materials that are acoustic absorptive are generally dense and structurally opaque, whereas materials that are highly solar-reflective are conventionally applied to hard, non-absorptive surfaces a materials-level conflict that existing multifunctional metasurfaces have not resolved at building scale. This paper addresses that gap by proposing a single ventilated meta-panel unit cell that couples an array of subwavelength Helmholtz resonators (for low-frequency traffic and HVAC noise attenuation while remaining air-permeable) with an exterior spectrally selective multilayer coating (for high solar reflectance and high mid-infrared emissivity, enabling passive daytime radiative cooling), placing the coating on the resonator rim rather than in the acoustic cavity so that neither function is physically compromised by the other. Using a literature-parameterised lumped-element acoustic model and a representative multilayer photonic spectral model, we perform a computational feasibility analysis and benchmark the design against sealed, ventilated-only and acoustic-only reference configurations reported in the literature. The key finding is that the proposed hybrid panel achieves an average sound transmission loss of approximately 18 dB over 500–2000 Hz, covering the dominant band of urban traffic and mechanical noise, together with a net radiative cooling power of approximately 60 W/m² under standard solar loading performance that sits within the ranges separately reported for acoustic-only and photonic-only panels, but is delivered by one shared ventilated structure rather than by stacking two separate systems. A parametric sensitivity analysis over resonator quality factor and coating reflectance/emissivity shows that both performance metrics remain within practically useful bounds across the parameter ranges reported in the cited literature. The principal academic contribution is a design-level demonstration, grounded in physically motivated models rather than assumption, that acoustic and radiative-cooling co-design is not physically precluded within one unit cell a conclusion that directly answers the co-design gap repeatedly flagged in recent review literature. In practical terms, the design offers a concrete route to building envelope retrofit panels that combine noise mitigation and passive cooling without the added mass, cost and space of separate acoustic and thermal systems, with potential relevance to dense urban buildings exposed to both traffic noise and solar heat gain. We report fabrication routes, durability considerations, and a concrete experimental validation agenda; the results presented are computational feasibility screening, and physical prototyping and laboratory/field characterisation remain necessary before the design can be considered validated for deployment.
Keywords: Metamaterials; acoustic metamaterials; photonic metamaterials; passive daytime radiative cooling; Helmholtz resonator; spectrally selective coating; building envelope; multifunctional metasurface; urban heat island; noise mitigation
[This article belongs to International Journal of Energy and Thermal Applications ]
References
1. Liu Z, Zhang X, Mao Y, Zhu YY, Yang Z, Chan CT, et al. Locally resonant sonic materials. Science. 2000;289(5485):1734-1736.doi:10.1126/science.289.5485.1734.
2. Pendry JB, Holden AJ, Robbins DJ, Stewart WJ. Magnetism from conductors and enhanced nonlinear phenomena. IEEE Trans Microw Theory Tech. 1999;47(11):2075-2084.doi:10.1109/22.798002.
3. Shelby RA, Smith DR, Schultz S. Experimental verification of a negative index of refraction. Science. 2001;292:77-79.doi:10.1126/science.1058847.
4. Smith DR, Padilla WJ, Vier DC, Nemat-Nasser SC, Schultz S. Composite medium with simultaneously negative permeability and permittivity. Phys Rev Lett. 2000;84(18):4184-4187.doi:10.1103/PhysRevLett.84.4184.
5. Pendry JB. Negative refraction makes a perfect lens. Phys Rev Lett. 2000;85:3966-3969.doi:10.1103/PhysRevLett.85.3966.
6. Pendry JB, Schurig D, Smith DR. Controlling electromagnetic fields. Science. 2006;312(5781):1780-1782.doi:10.1126/science.1125907.
7. Schurig D, Mock JJ, Justice BJ, Cummer SA, Pendry JB, Starr AF, et al. Metamaterial electromagnetic cloak at microwave frequencies. Science. 2006;314(5801):977-980.doi:10.1126/science.1133628.
8. Guo C, Luo Y. Light people: Prof. Sir John Pendry, father of metamaterials, spoke about the future of meta. Light Sci Appl. 2023;12:45.doi:10.1038/s41377-023-01082 w.
9. Tamasauskaite-Tamasiunaite L, Dordi Y, Norkus E, Stankeviciene I, Jagminiene A, Naujokaitis A, et al. Electroless platinum deposition using Co3+/Co2+ redox couple as a reducing agent. Materials (Basel). 2021;14(8):1893.doi:10.3390/ma14081893.
10. Raman AP, Anoma MA, Zhu L, Rephaeli E, Fan S. Passive radiative cooling below ambient air temperature under direct sunlight. Nature. 2014;515:540-544.doi:10.1038/nature13883.
11. Fang H, Zhao D, Yuan J, Aili A, Yin X, Yang R, et al. Performance evaluation of a metamaterial- based new cool roof using improved Roof Thermal Transfer Value model. Appl Energy. 2019;248:589-599.doi:10.1016/j.apenergy.2019.04.116.
12. Wang W, Fernandez N, Katipamula S, Alvine K. Performance assessment of a photonic radiative cooling system for office buildings. Renew Energy. 2018;118:265-277.doi:10.1016/j.renene.2017.10.062.
13. Yang Z, Mei J, Yang M, Chan NH, Sheng P. Membrane-type acoustic metamaterial with negative dynamic mass. Phys Rev Lett. 2008;101(20):204301.doi:10.1103/PhysRevLett.101.204301.
14. Sui N, Yan X, Huang TY, Xu J, Yuan FG, Jing Y. A lightweight yet sound-proof honeycomb acoustic metamaterial. Appl Phys Lett.2015;106:171905.doi:10.1063/1.4919235.
15. Li J, Shi Y, Jiang R, Zhang Z, Huang Q. Acoustic insulation mechanism of membrane-type acoustic metamaterials loaded with arbitrarily shaped mass blocks of variable surface density. Materials (Basel). 2022;15(4):1556.doi:10.3390/ma15041556.
16. Jiang R, Shi G, Huang C, Zheng W, Li S. Acoustic insulation characteristics and optimal design of membrane-type metamaterials loaded with asymmetric mass blocks. Materials (Basel). 2023;16(3):1308 doi: 10.3390/ma16031308
17. Jang JY, Park CS, Song K. Lightweight soundproofing membrane acoustic metamaterial for broadband sound insulation. Mech Syst Signal Process. 2022;178:109270.doi:10.1016/j.ymssp.2022.109270.
18. Piracha A, Chaudhary MT. Urban air pollution, urban heat island and human health: a review of the literature. Sustainability. 2022;14:9234.doi:10.3390/su14159234.
19. Nature Index. Thermal metamaterials and heat flux manipulation. Nature Index Topic Review. 2024. Available from: https://www.nature.com/nature index/topics/l4/thermal-metamaterials-and- heat-flux-manipulation
20. Kim SH, Lee SH. Air transparent soundproof window. AIP Adv. 2014;4(11):117123.doi:10.1063/1.4902155.
21. Mir F, Mandal D, Banerjee S. Metamaterials for acoustic noise filtering and energy harvesting. Sensors (Basel). 2023;23(9):4227.doi:10.3390/s23094227.
22. Ma F. Acoustic and mechanical metamaterials for various applications: a brief review. Front Mater. 2025;12:1626945.doi:10.3389/fmats.2025.1626945.
23. Ghaffarivardavagh R, Nikolajczyk J, Anderson S, Zhang X. Ultra-open acoustic metamaterial silencer based on Fano-like interference. Phys Rev B. 2019;99(2):024302.doi:10.1103/PhysRevB.99.024302.
24. Arjunan A, Baroutaji A, Robinson J, Vance A, Arafat A. Acoustic metamaterials for sound absorption and insulation in buildings. Build Environ. 2024;251:111250.doi:10.1016/j.buildenv.2024.111250.
25. Morandi F, Prato A, Barbaresi L, Schiavi A. On the diffuseness of the vibrational field of a cross-laminated timber plate: comparison between theoretical and experimental methods. Appl Acoust. 2020;159:107104.doi:10.1016/j.apacoust.2019.107104.
26. Sugahara A, Lee H, Sakamoto S, Takeoka S. Measurements of acoustic impedance of porous materials using a parametric loudspeaker with phononic crystals and phase-cancellation method. Appl Acoust. 2019;152:54-62.doi:10.1016/j.apacoust.2019.03.019.
27. Wang C, Elson J, Lin Y, Liu S. The influence of temperature and interior ambient lighting color on nighttime driving performance. Build Environ. 2025;275:112815.doi:10.1016/j.buildenv.2025.112815.
28. Ventilated metamaterials for broadband sound insulation and tunable transmission at low frequency. Mater Today Phys. 2021.doi:10.1016/j.mtphys.2021.100387.
29. Tang Z, Wang X, Li S, Li H, Zhu Z, Ma F. A transparent multifunctional integrated meta-window with excellent sound insulation and vibration reduction performance. Compos Struct. 2025;353:118719.doi:10.1016/j.compstruct.2024.118468.
30. Yuan J, Yin H, Yuan D, Yang Y, Xu S. On daytime radiative cooling using spectrally selective metamaterial based building envelopes. Energy. 2022;242:122779.doi:10.1016/j.energy.2021.122779.
31. Design strategies, manufacturing, and applications of radiative cooling technologies. Nanophotonics. 2025;14(14):2355-95. doi:10.1515/nanoph-2025-0159. PMCID: PMC12273545.
32. Yu XQ, Li F, Wang J, Zhang N, Li GX, Song Y, et al. Scalable-designed photonic metamaterial for color-regulating passive daytime radiative cooling. Nano-Micro Lett. 2026;18:153.doi:10.1007/s40820-025-01975-y.
33. Techno-economic and environmental evaluation on radiative sky cooling-based novel passive envelope strategies to achieve building sustainability and carbon neutrality. Energy Convers Manage. 2023.doi:10.1016/j.enconman.2023.117639.
34. Bilateral passive thermal management for dynamical temperature regulation using VO2-based photonic metastructures. Cell Rep Phys Sci. 2024.
35. Sun K, Riedel CA, Urbani A, Simeoni M, Mengali S, Zalkovskij M, et al. VO2 thermochromic metamaterial-based smart optical solar reflector. ACS Photonics. 2018;5(6):2280-6.doi:10.1021/acsphotonics.8b00119.
36. Wang S, Jiang T, Meng Y, Yang R, Tan G, Long Y. Scalable thermochromic smart windows with passive radiative cooling regulation. Science. 2021;374(6574):1501-4. doi:10.1126/science.abg0291.
37. Jiang C, He L, Xuan Q, Liao Y, Dai JG, Lei D. Phase-change VO2-based thermochromic smart windows. Light Sci Appl. 2024;13:273. doi:10.1038/s41377-024-01560-9.
38. Li SY, Niklasson GA, Granqvist CG. Thermochromic fenestration with VO2-based materials: three challenges and how they can be met. Thin Solid Films. 2012;520(10):3823-8. f[
39. Ma G, Sheng P. Acoustic metamaterials: from local resonances to broad horizons. Sci Adv. 2016;2(2):e1501595. doi:10.1126/sciadv.1501595.
40. Ha CS, Yao D, Xu Z, Liu C, Liu H, Elkins D, et al. Rapid inverse design of metamaterials based on prescribed mechanical behavior through machine learning. Nat Commun. 2023;14:5943.doi:10.1038/s41467-023-40854-1.
41. Fan S, et al. Thermal cloaking via transformation thermotics [Preprint]. arXiv:1411.0212. 2014. Available from: https://arxiv.org/abs/1411.0212.
42. Peralta I, Fachinotti VD, Álvarez Hostos JC. A brief review on thermal metamaterials for cloaking and heat flux manipulation. Adv Eng Mater. 2020;22(2):1901034. doi:10.1002/adem.201901034.
43. Xu L, Huang J. Metamaterials for manipulating thermal radiation: transparency, cloak, and expander. Phys Rev Appl. 2019;12(4):044048. doi:10.1103/PhysRevApplied.12.044048.
44. Park G, Kang S, Lee H, Choi W. Tunable multifunctional thermal metamaterials: manipulation of local heat flux via assembly of unit-cell thermal shifters. Sci Rep. 2017;7:41000. doi:10.1038/srep41000.
45. Liu D, Tan Y, Khoram E, Yu Z. Training deep neural networks for the inverse design of nanophotonic structures. ACS Photonics. 2018;5(4):1365-9. doi:10.1021/acsphotonics.7b01377.
46. Kim J, Torquato S. Multifunctional composites for elastic and electromagnetic wave propagation [Preprint]. arXiv:1908.06662. 2019. Available from: https://arxiv.org/abs/1908.06662.
47. Santamouris M, Cartalis C, Synnefa A, Kolokotsa D. On the impact of urban heat island and global warming on the power demand and electricity consumption of buildings: a review. Energy Build. 2015;98:119-24.doi:10.1016/j.enbuild.2014.09.052.
48. Li X, Zhou Y, Yu S, Jia G, Li H, Li W. Urban heat island impacts on building energy consumption: a review of approaches and findings. Energy. 2019;174:407-19. doi:10.1016/j.energy.2019.02.183.
49. Mekonnen GT, Berlie AB, Wubie M, Legesse SA. Surface urban heat island intensity and urban utility consumption: impact analysis and projections. ScientificWorldJournal. 2025;2025:3250112.doi:10.1155/tswj/3250112. PMCID: PMC11876520.
50. Esfandiari M, Zhu J, Yang Y. Additively manufactured metasurfaces and metamaterials: designs, fabrications, and applications from microwave to photonics. APL Photonics. 2025;10(4):041101 doi:10.1063/5.0241299.
International Journal of Energy and Thermal Applications
| Volume | 04 | |
| Issue | 02 | |
| Received | 09/07/2026 | |
| Accepted | 30/07/2026 | |
| Published | 25/08/2026 | |
| Publication Time | 47 Days |