Open Access
![](http://storage.googleapis.com/journals-stmjournals-com-wp-media-to-gcp-offload/2022/10/vector.jpg)
Devan Naveen Kumar,
![](http://storage.googleapis.com/journals-stmjournals-com-wp-media-to-gcp-offload/2022/10/vector.jpg)
T. Vijayakumar,
![](http://storage.googleapis.com/journals-stmjournals-com-wp-media-to-gcp-offload/2022/10/vector.jpg)
G. Murali,
- PG Student Department of Mechanical Engineering, Koneru Lakshmaiah Education Foundation Andhra Pradesh India
- Associate Professor Department of Mechanical Engineering, Koneru Lakshmaiah Education Foundation Andhra Pradesh India
- Professor Department of Mechanical Engineering, Koneru Lakshmaiah Education Foundation Andhra Pradesh India
Abstract
Automobile manufacturers are currently dedicated to enhancing vehicle speeds for the purpose of saving travel time. However, achieving this objective necessitates the use of friction materials capable of handling high-speed braking. In this article, we will delve into the historical evolution of materials utilized for brake pads and drums. In the past, asbestos stood out as the most widely employed brake lining material due to its effectiveness. Unfortunately, its carcinogenic properties led to its prohibition by health and environmental agencies. Consequently, endeavors were undertaken to create brake friction materials devoid of asbestos. Presently, non-asbestos organic brake pads have become the most prevalent choice, despite the generation of harmful wear debris. To drive progress, scientists are energetically involved in developing environmentally sustainable brake friction materials that can perform effectively in high-speed braking under various weather conditions. They are exploring options like natural fibers or materials derived from agricultural waste as potential alternatives for brake pads. When it comes to brake discs and drums, cast iron has historically been the conventional choice. Nonetheless, more recent materials such as aluminum matrix composites, carbon-carbon composites, and ceramics are gaining popularity. Among these, aluminum matrix composite is particularly promising due to its low density and improved braking stability. Consequently, it is considered a potential future material for brake discs or drums.
Keywords: Brake Pad, Brake Disc, Brake Drum, Metal Matrix Composites, Non-Asbestos Materials.
This article belongs to Special Issue Conference International Conference on Innovative Concepts in Mechanical Engineering (ICICME – 2023)
Browse Figures
References
- Venkatesh et.al, Scoping Review of Brake Friction Material for Automotive, Materials Today: Proceedings,2019, (16), 927–933.
- Blau PJ, Meyer III HM. Case Study: Characteristics of wear particles produced during friction tests of conventional and unconventional disc brake materials. Wear. 2003;255(7-12): 1261–1269.
- Gowthami et.al, Designing and Analysis of Brake Drum. International Journal for Research in Applied Science & Engineering Technology. 2016;4(9): 135–142.
- Chandgude et.al, Review on development of composite material for disc brake pad [JETIR]. J Emerg Technol Innov Res. 2016;3(5):63–5
- Rao RU, Babji G. A Review paper on alternate materials for Asbestos brake pads and its characterization. International Research Journal of Engineering and Technology. 2015;2(2):
556–562. - Lee K, Park K. Optimal robust control of a contactless brake system using an eddy current. Mechatronics. 1999;9(6): 615–631.
- Maluf O et.al, Development of materials for automotive disc brakes. Minerva. 2007;4(2):
149–158. - Santhosh Kumar, Subrata Kumar Ghosh, Particle emission of organic brake pad material: A review, Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering. 2019; (234):1213–1223
- Eriksson M and Jacobson S. Tribological surfaces of organic brake pads. Tribol Int 2000; 33: 817–882
- Marzocchi, A., Jannarelli, A. E. and Garrett, D. W. Friction materials for brake linings and the like. US Pat. 3967037, 1976 (United States Patent and Trademark Office).
- Holman, J. P. Heat Transfer, 8th edition, pp. 641–642 (McGraw-Hill, Singapore).
- Hell, M., Jaworek, W., Huppatz, W. and Wieser, D. Friction lining, especially for brakes and clutches, and a method for producing a friction lining. US Pat. 6481555, 2002 (United States Patent and Trademark Office).
- Okubo, H. S., Albertson, C. E. and Nibert, R. K. Asbestos-free friction materials. US Pat. 4446203, 1984 (United States Patent and Trademark Office).
- Smith, W. N. and Boyd, P. Carbonaceous friction materials. US Pat. 5965658, 1999 (United States Patent and Trademark Office).
- Warren, R. Ceramic-Matrix Composites, 1992, p. 2 (Blackie, New York).
- Chan and G W Stachowiak Review of automotive brake friction materials Proc. Instn Mech. Engrs Vol. 218,p 953–965.
- Critchley, J. P., Knight, G. J. and Wright, W. W. Heat-Resistant Polymers, 1983, pp. 21–29 (Plenum Press, New York)
- Komori, T., Miyake, S. and Senoo, Y. Brake friction material. US Pat. 4954536, 1990 (United States Patent and Trademark Office).
- Ohya, K. and Kimbara, H. Disc brake pad. US Pat. 4944373, 1990 (United States Patent and Trademark Office).
- Kamioka, N., Tokumura, H. and Yoshino, T. Friction material containing BT resin dust. US Pat. 5384344, 1995 (United States Patent and Trademark Office).
- Kinouchi, S., Hara, Y. and Yamaguchi, J. Friction material composition, production of the same and friction material. US Pat. 6372817, 2002 (United States Patent and Trademark Office).
- The exfoliation of vermiculite. Report 23, Western Australian Mining and Petroleum Research Institute, 1989
- Komori, T., Miyake, S. and Senoo, Y. Brake friction material. US Pat. 4954536, 1990 (United States Patent and Trademark Office)
- Kobayashi, M. Non-asbestos friction materials. US Pat. 6413622, 2002 (United States Patent and Trademark Office).
- Hulskotte JHJ, Roskam GD, Denier van der Gona HAC. Elemental composition of current automotive braking materials and derived air emission factors. Atmospheric Environment. 2014;99: 436–445.
- Maluf O, Angeloni M, Milan MT, Spinelli D, Filho WWB. Development of materials for automotive disc brakes. Minerva. 2007;4(2): 149–158.
- Belhocine A, Bouchetara M. Temperature and Thermal Stresses of Vehicles Gray Cast Brake. Journal of Applied Research and Technology. 2013;11: 674–682.
- Lyu Y, Olofsson U. On black carbon emission from automotive disc brakes. Journal of Aerosol Science. 2020;148: 105610.
- Mackin TJ. Thermal Cracking in Disc Brakes. Engineering failure Analysis. 2002;9: 63–76.
- Cueva G, Sinatora A, Guesser WL, Tschiptschin AP. Case Study: Wear resistance of cast irons used in brake disc rotors. Wear. 2003;255: 1256–1260.
- Natarajan N, Vijayarangan S, Rajendran I. Fabrication, testing and thermal analysis of metal matrix composite brake drum. Int J Vehicle Design. 2007;44: 339–359. 810 Naveen Kumar, Ajaya Bharti, H.S. Goyal, Kunvar Kant Patel
- Blau PJ, McLaughlin JC. Effects of water films and sliding speed on the frictional behavior of truck disc brake materials. Tribology International. 2003;36: 709–715.
- Blanco C, Bermejo J, Marsh H, Menendez R. Chemical and physical properties of carbon as related to brake performance. Wear. 1997;213: 1–12.
- Xiao Y, Zhang Z, Yao P, Fan K, Zhou H, Gong T, Zhao L, Deng M. Mechanical and tribological behaviors of copper metal matrix composites for brake pads used in high-speed trains. Tribology International. 2018;119: 585–592.
- Panier S, Dufrénoy P, Weichert D. An experimental investigation of hot spots in railway disc brakes. Wear. 2004;256: 7764–7773.
- Desplanques Y, Roussette O, Degallaix G, Copin R, Berthier Y. Analysis of tribological behaviour of pad–disc contact in railway braking Part 1. Laboratory test development, compromises between actual and simulated tribological triplets. Wear. 2007;262: 582–591.
- Ma X, Fan S, Sun H, Luan C, Deng J, Zhang L, Cheng L. Investigation on braking performance and wear mechanism of full-carbon/ceramic braking pairs. Tribology International. 2020;142: 105981.
- Tayeb NSME, Liew KW. Effect of water spray on friction and wear behaviour of noncommercial and commercial brake pad materials. Journal of Materials Processing Technology. 2008;208: 135–144.
- Blanco C, Bermejo J, Marsh H, Menendez R. Chemical and physical properties of carbon as related to brake performance. Wear. 1997;213: 1–12.
- Stadler Z, Krnel K, Kosmac T. Friction and wear of sintered metallic brake linings on a C/C-SiC composite brake disc. Wear. 2008;265: 278–285.
- Blanco C, Bermejo J, Marsh H, Menendez R. Chemical and physical properties of carbon as related to brake performance. Wear. 1997;213: 1–2.
- Samal P, Vundavilli PR. Dry Sliding Wear Performances of AA5052 Hybrid Composite Brake Disc Materials Reinforced with In Situ Synthesized TiC and Multi-Walled Carbon Nanotube. ASME Journal of Tribology, 2023; 145:1–15.
- Samal P, Surekha B, Vundavilli PR. Experimental Investigations on Microstructure, Mechanical Behavior and Tribological analysis of AA5154/SiC Composites by Stir Casting. 2022; 14:3317–3328.
- Jang H, Ko K, Kim SJ, Basch RH, Fash JW. The effect of metal fibers on the friction performance of automotive brake friction materials. Wear. 2004;256: 406–414.
- Shorowordi KM, Haseeb ASMA, Celis JP. Velocity effects on the wear, friction and tribochemistry of aluminum MMC sliding against phenolic brake pad. Wear. 2004;256: 1176–1181.
- Uyyuru RK, Surappa MK, Brusethaug S. Effect of reinforcement volume fraction and size distribution on the tribological behavior of Al-composite/brake pad tribo-couple. Wear. 2006;260: 1248–1255.
- Samal P, Vundavilli PR, Meher A, Mahapatra MM. Influence of TiC on dry sliding wear and mechanical properties of in situ synthesized AA5052 metal matrix composites. Journal of Composite Materials, 2019; 53:4323–4336.
- Gowthami K, Balaji K. Designing and Analysis of Brake Drum. International Journal for Research in Applied Science & Engineering Technology. 2016;4(9): 135–142.
- Zhang SY, Qu SG, Li YY, Chen WP. Two-body abrasive behavior of brake pad dry sliding against interpenetrating network ceramics/Al-alloy composites. Wear. 2010;268: 939–945.
- Podratzky A, Bansemir H. Design and experimental characterization of modern helicopters rotor brakes. Aerospace Science and Technology. 2007;11: 360–369.
- Bian G, Wu H. Friction performance of carbon/silicon carbide ceramic composite brakes in ambient air and water spray environment. Tribology International. 2015;92: 1–11.
- Günay M, Korkmaz ME, Özmen R. An investigation on braking systems used in railway vehicles. Engineering Science and Technology, an International Journal. 2020;23: 421–431.
- Jiang L, Jiang Y, Yu L, Yang H, Li Z, Ding Y, Fu GF. Fabrication, microstructure, friction and wear properties of SiC3D/Al brake disc−graphite/SiC pad tribo-couple for highspeed train. Trans Nonferrous Met Soc China. 2019;29(9): 1889–1902.
- Meher A, Mahapatra MM, Samal P, Vundavilli PR. A review on manufacturability of magnesium matrix composites: Processing, tribology, joining, and machining. CIRP Journal of Manufacturing Science and Technology. 2022; 39:134–158.
- Chapman TR, Niesz DE, Fox RT, Fawcett T. Wear-resistant aluminum-boron-carbide cermets for automotive brake applications. Wear. 1999;236: 81–87.
- Kermc M, Kalin M, Vizintin J. Development and use of an apparatus for tribological evaluation of ceramic-based brake materials. Wear. 2005;259: 1079–1087.
- Stadler Z, Krnel K, Kosmac T. Friction behavior of sintered metallic brake pads on a C/C–SiC composite brake disc. Journal of the European Ceramic Society. 2007;27: 1411–1417.
- Stadler Z, Krnel K, Kosmac T. Friction and wear of sintered metallic brake linings on a C/C-SiC composite brake disc. Wear. 2008;265: 278–285.
- Samal P, Vundavilli PR, Meher A, Mahapatra MM. Recent progress in aluminum metal matrix composites: A review on processing, mechanical and wear properties. Journal of Manufacturing Processes. 2020; 59: 131–152.
- Desplanques Y, Roussette O, Degallaix G, Copin R, Berthier Y. Analysis of tribological behaviour of pad–disc contact in railway braking Part 1. Laboratory test development, compromises between actual and simulated tribological triplets. Wear. 2007;262: 582–591.
- Tayeb NSME, Liew KW. Effect of water spray on friction and wear behaviour of noncommercial and commercial brake pad materials. Journal of Materials Processing Technology. 2008;208: 135–144.
- Abhik R, V. U, Xavior MA. Evaluation of Properties for Al-SiC Reinforced Metal Matrix Composite for Brake Pads. Procedia Engineering. 2014;97: 941–950.
![](http://storage.googleapis.com/journals-stmjournals-com-wp-media-to-gcp-offload/2022/12/af025f00-jopc.jpg)
Journal of Polymer and Composites
Volume | 11 |
Special Issue | 08 |
Received | October 19, 2023 |
Accepted | November 28, 2023 |
Published | January 31, 2024 |