Open Access
Dhanraj Sampat Kakade
Aniket Dilip Borde
Chintan Dattatray Chougule
Prathamesh Sandeep Chindarkar
Madan Jagtap
- Student, Saraswati College of Engineering, Navimumbai, Maharashtra, India
- Student, Saraswati College of Engineering, Navimumbai, Maharashtra, India
- Student, Saraswati College of Engineering, Navimumbai, Maharashtra, India
- Student, Saraswati College of Engineering, Navimumbai, Maharashtra, India
- Professor, Saraswati College of Engineering, Navimumbai, Maharashtra, India
Abstract
This research work focuses on the composite material named S-Glass fibre Heat Exchanger, since the existing designs of heat exchangers are generally made up of metals which produce a critical amount of heat loss to the surrounding from the shell. These are also less corrosive resistant, have low life and high weight. To overcome these drawbacks, use of composite materials has become essential. There is a need to redesign it using composite materials which are lightweight, high strength material and more corrosion resistant.
Keywords: S-Glass, heat exchanger, composite material
[This article belongs to Journal of Thermal Engineering and Applications(jotea)]
Browse Figures
References
1. Sreejith K, Basil Varghese, Deepak Das, Delvin Devassy, Harikrishnan K, Sharath GK. Design and Cost Optimization of Plate Heat Exchanger. Int J Eng Sci. 2014 Oct; 4(10): 43–48, ISSN (e): 2278-4721, ISSN (p): 2319-6483.
2. Vindhya Vasiny Prasad Dubey, Raj Rajat Verma, Piyush Shanker Verma, Srivastava AK. Performance Analysis of Shell & Tube Type Heat Exchanger under the Effect of Varied Operating Conditions. IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE). 2014 May–Jun; 11(3) Ver. VI: 8–17. ISSN: 2278-1684, P-ISSN: 2320-334X.
3. Patil Rajendra P, Atul Patil, Patil Vijay H, Koli TA. Analysis of Steady State Heat Conduction in Different Composite Wall. International Journal of Innovative Research in Science, Engineering and Technology (IJIRSET). 2015 Jul; 4(7): 5394–5400. ISSN (Online): 2319-8753, ISSN (Print): 2347-6710.
4. Quade Derek J, Meador Michael A, Shin Euy-Sik E, Johnston James C, Kuczmarski Maria A. The design, fabrication, and testing of composite heat exchanger coupons. NASA Glenn Research Center, Cleveland, Ohio. 44135, Ohio Aerospace Institute, Cleveland, Ohio. 44142.
5. Pratapa Reddy Y, Jithendra Kumar B, Srinivasulu D, Ch Srinivasa Rao. Temperature Distribution Analysis of Composite Pin Fin By Experimental and Finite Element Method. International Journal of Innovative Research in Science, Engineering and Technology (IJIRSET). 2015 Oct; 4(10): 10121–10128. ISSN (Online) :2319-8753 ISSN (Print) : 2347-6710.M. Young, The Technical Writer’s Handbook. Mill Valley, CA: University Science, 1989.
6. Isa Ahmadi and M.M. Aghdam,” Heat transfer in composite materials using a new truly local meshless method”,” International Journal of Numerical Methods for Heat & Fluid Flow”,Vol. 21 No. 3, 2011 p. 293-309.
7. “Composite Material Handbook”, Vol. 2 Polymer Matrix Composites Material Properties, Department of Defence handbook, 17 June 2002.
8. F.C. Campbell, “Structural Composite Materials”, “Introduction to Composite Materials”.
9. L. Zaheed, R.J.J. Jachuck, “Review of polymer compact heat exchangers, with special emphasis on a polymer film unit”, “Applied Thermal Engineering”, 24 (2004) 2323–2358.
10. Ambekar Aniket Shrikant, R. Sivakumar, M. Vivekanandan,” Comparison of Shell and Tube Heat Exchanger using Theoretical Methods, HTRI, ASPEN and SOLIDWORKS simulation softwares”, Vol. 6, Issue 3, (Part -5) March 2016.
Journal of Thermal Engineering and Applications
| Volume | 8 |
| Issue | 1 |
| Received | June 23, 2021 |
| Accepted | June 30, 2021 |
| Published | June 30, 2023 |