Effect of WEDM Machining Parameter on the MMC: A Review

Year : 2023 | Volume :01 | Issue : 01 | Page : 1-7
By

Ashwin Ghaysundar,

Mahendra J. Sable,

Dilip M. Patel,

Asmita A. Bagade,

Shriram Shastri Chavali,

  1. Ph.D Scholar, Department of Mechanical Engineering, D.N. Patel College of Engineering Shahada, Maharashtra, India
  2. Professor, Department of Mechanical Engineering, COEP Technological University, Maharashtra, India
  3. Professor, Department of Mechanical Engineering, Shri Jaykumar Rawal Institute of Technology, Maharashtra, India
  4. Ph.D Scholar, Department of Mechanical Engineering, D Y Patil School of Engineering & Technology Ambi, Maharashtra, India
  5. Professor, Department of Mechanical Engineering, D Y Patil School of Engineering & Technology Ambi, Maharashtra, India

Abstract

Recent area of manufacturing is highly focus on good accuracy and a complex shapes are mechanized by the advanced machining operation. The wire electrical discharge machining (WEDM) have the ability to produce the complex shapes with having high accuracy. The WEDM is non-contact type machining operation and is used for metal materials as well as Metal Matrix Composites (MMCs), ceramics composites those have many application in vast areas such as defence, aircraft, automobile sector, medical equipment’s, agriculture machines, etc. As the requirement of metal properties such as light weight, good wear resistance, low density, high strength which can be possible due to combinations of two or more materials and this materials called as Metal matrix composites. The Aluminium is widely used as a base metal in MMCs along with varying reinforcement particles such as B4C, Al2O3, TiO2, ZrO2, SiC. The most of the researchers are studied on the WEDM parameters, process modelling, electrode materials, dielectric medium, etc. The considerable input parameter is the focusing area for improved Material Removal Rate, Surface Roughness and Kerf-width of composite. For a more thorough comprehension of the research conducted in this field, the diversity of studies must be categorized. This study analyzes the processing of MMCs, including the approaches taken, the results and a summary of the review. The future directions of the same field’s study are also discussed in the paper.

Keywords: WEDM, AlMMC, Reinforcement, composites

[This article belongs to International Journal of Fracture Mechanics and Damage Science (ijfmds)]

How to cite this article:
Ashwin Ghaysundar, Mahendra J. Sable, Dilip M. Patel, Asmita A. Bagade, Shriram Shastri Chavali. Effect of WEDM Machining Parameter on the MMC: A Review. International Journal of Fracture Mechanics and Damage Science. 2024; 01(01):1-7.
How to cite this URL:
Ashwin Ghaysundar, Mahendra J. Sable, Dilip M. Patel, Asmita A. Bagade, Shriram Shastri Chavali. Effect of WEDM Machining Parameter on the MMC: A Review. International Journal of Fracture Mechanics and Damage Science. 2024; 01(01):1-7. Available from: https://journals.stmjournals.com/ijfmds/article=2024/view=132673

References

1. R. Kandan1 J. et al. “Investigation of Mechanical Properties on Newly Formulated Hybrid Composite Aluminium 8011 Reinforced With B4C and Al2O3 by Stir Casting Method” IJSRD, Vol. 5, Issue 01, 2017 | ISSN (online): 2321–0613
2. Pankaj K Gupta and MK Gupta. “Mechanical and microstructural analysis of Al-Al2O3/B4C hybrid composites” J Materials: Design and Applications 0(0) 1–12, IMechE 2020
3. T.Hariprasada, K.Varatharajanb, S.Ravic “Wear Characteristics of B4C and Al2O3 Reinforced with Al 5083 Metal Matrix based Hybrid Composite” Proceedia Engineering 97 (2014) 925–929
4. Toptan F, Kilicarslan A, et al. “Processing and micro structural characterization of AA1070 and AA6063 matrix B4Cp reinforced composites”. Materials and Design 2010; 31: 987–91.
5. Hammar Ilham Akbar, et al., “Effect of Reinforcement Material on Properties of Manufactured Aluminum Matrix Composite Using Stir Casting Route” 6th International Conference on
Industrial, Mechanical, Electrical and Chemical Engineering (ICIMECE 2020),62–68.
6. M. O. Bodunrin et al. “Aluminium matrix hybrid composites: a review of reinforcement philosophies; mechanical, corrosion and tribological characteristics.” 2238–7854/© 2015 Brazilian Metallurgical, Materials and Mining Association. http://dx.doi.org/10.1016/j.jmrt.2015.05.003
7. V. Kavimani et al. “Multi-objective optimization in WEDM process of grapheme–SiC magnesium composite through hybrid techniques” Measurement 145(2019)335–349 https://doi.org/10.1016/j.measurement.2019.04.076
8. RAJMOHAN1 “Evaluation of mechanical and wear properties of hybrid aluminium matrix composites” Trans. Nonferrous Met. Soc. China 23(2013) 2509−2517. DOI: 10.1016/S1003-6326(13)62762-4
9. Ashwin G Ghaysundar et al. “A SHORT REVIEW ON AL MMC WITH REINFORCEMENT EFFECTS ON THEIR MECHANICAL PROPERTIES.” Eur. Chem. Bull. 2023, 12(10), 9102–9110 ISSN 2063-5346 DOI: https://doi.org/10.48047/ecb/2022.12.10.6452023.02/08/2023 https://eurchembull.com/uploads/paper/4a56cc06d27f7291c6868f4ecb31a035.pdf
10. Prashantha S1 et al. “A Study on Machining Characteristics of A6061-Sic Metal Matrix Composite through wire- cut Electro Discharge Machining” Materials Today: Proceedings 4
(2017) 10779–10785
11. H. Majumder1 et al. “Predictive Analysis on Responses in WEDM of Titanium Grade 6 Using General Regression Neural Network (GRNN) and Multiple Regression Analysis (MRA)” Silicon Springer Science+Business Media B.V. 2018 https://doi.org/10.1007/s12633-017-9667-1
12. Mangesh R. Phate1, “Multi-parametric Optimization of WEDM Using Artificial Neural Network (ANN)-Based PCA for Al/SiCp MMC” The Institution of Engineers (India) 2020 https://doi.org/10.1007/s40032-020-00615-1
13. Adeel Ikram “Parametric optimization for surface roughness, kerf and MRR in wire electrical discharge machining (WEDM) using Taguchi design of experiment” Journal of Mechanical Science and Technology 27 (7) (2013) 2133~2141 DOI 10.1007/s12206-013-0526-8

14. Sonawane, S.A., Kulkarni, M.L., Optimization of machining parameters of WEDM for Nimonic-75 alloy using principal component analysis integrated with Taguchi method, Journal of King Saud University – Engineering Sciences (2018), DOI: https://doi.org/10.1016/j.jksues.2018.04.001

15. R. N. Ahmad et al. “Primary study on machinability of aluminium matrix composite using WEDM” IJET-IJENS vol.: 10 No: 06 (2010)
16. M. Ravikumar1 et al. “Study on Mechanical and Tribological Characterization of Al2O3/SiCp Reinforced Aluminum Metal Matrix Composite” Springer Science+Business Media B.V., part of
Springer Nature 2018 https://doi.org/10.1007/s12633-018-9788-1
17. Abhay S. Gore et al. “Wire electro discharge machining of metal matrix composites: A review” Procedia Manufacturing 20 (2018) 41–52 10.1016/j.promfg.2018.02.006
18. Tigabu Abebe et al. “Kerf width analysis of wire electrical discharge machining of titanium alloy (Ti-6Al-4 V ELI) using response surface method” Materials Todays Proceedings Volume 62, Part 2, 2022, Pages 481–487 https://doi.org/10.1016/j.matpr.2022.03.571


Regular Issue Subscription Review Article
Volume 01
Issue 01
Received 20/10/2023
Accepted 12/11/2023
Published 08/02/2024