Design Analysis of PALF Natural Fiber Composite Laminate under Tensile Loading Condition using Simulation Approach

Year : 2024 | Volume :01 | Issue : 02 | Page : 23-29
By

Raja Srikanth

Dr. Shaik Khadar Vali

Dr. K. Saraswathamma

S. Irfan Sadaq

  1. Research Scholar Mechanical Engineering Department, University College of Engineering, Osmania University, Hyderabad Telangana India
  2. Professor Mechanical Engineering Department, Muffakham Jah College of Engineering and Technology, Hyderabad Telangana India
  3. Professor Mechanical Engineering Department, University College of Engineering, Osmania University, Hyderabad Telangana India
  4. Assistant Professor Mechanical Engineering Department, Muffakham Jah College of Engineering and Technology, Hyderabad Telangana India

Abstract

Plant-based fibre reinforced materials are increasingly being employed for a variety of structural and non-structural purposes. Plant and animal-based fibres have different characteristics depending on a variety of circumstances. Mechanical qualities are primarily determined by parameters such as matrix, fillers, fibre content, fibre treatment, and fabrication techniques. The present work aim in analyzing the PALF natural fiber using simulation approach. In the process laminates are prepared as per ASTM standards in simulation software and tensile load is applied to study the behavior of laminate considering their deformation and stress. A variety of helix angle are chosen to study the same. From the observation it is observed that 60O and 90O are the optimum helix angle found the study where the deformation and strains are observed to be low when compared with other helix angles.

Keywords: Natural Fiber, Helix angle, Tensile strength, Deformation, Strain

[This article belongs to International Journal of Fracture Mechanics and Damage Science(ijfmds)]

How to cite this article: Raja Srikanth, Dr. Shaik Khadar Vali, Dr. K. Saraswathamma, S. Irfan Sadaq. Design Analysis of PALF Natural Fiber Composite Laminate under Tensile Loading Condition using Simulation Approach. International Journal of Fracture Mechanics and Damage Science. 2024; 01(02):23-29.
How to cite this URL: Raja Srikanth, Dr. Shaik Khadar Vali, Dr. K. Saraswathamma, S. Irfan Sadaq. Design Analysis of PALF Natural Fiber Composite Laminate under Tensile Loading Condition using Simulation Approach. International Journal of Fracture Mechanics and Damage Science. 2024; 01(02):23-29. Available from: https://journals.stmjournals.com/ijfmds/article=2024/view=140812


Browse Figures

References

  1. Abdalla F. H.1, Megat M. H.1, Sapuan M. S. and B. B. Sahari ; “Determination of volume fraction values of filament wound glass and carbon fiber reinforced composites”. Department of Mechanical and Manufacturing Engineering, University Putra Malaysia, Serdang, Selangor, Malaysia Institute of Advanced Technology, ITMA, University Putra Malaysia, Serdang, Selangor, Malaysia
  2. Broyles N. S., Verghese K. N. E., Davis S. V., Li H., Davis R. M., Lesko J. J. and Riffle J. S. 1998. Fatigue performance of carbon fiber/vinyl ester composites: the effect of two dissimilar polymeric sizing agents. Polymer. 39(15): 3417-3424.
  3. Donald F. Adams, Leif A. Carlsson and R. Byron Pipes. 2003. Experimental characterization of advanced composite materials. 3rd by CRC PRESS LLC.
  4. Lyon, R, Schumann, D, & DeTeresa, S. “Matrix-Dominated Mechanical Properties of a Fiber Composite Lamina.” Eleventh Volume: Composite Materials—Testing and Design. Camponeschi, E, Jr. 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959: ASTM International, 1993.
  5. Binshan S. Y., Alrik L. Svenson and Lawrence C. Bank. 1995. Mass and Volume Fraction Properties of Pultruded Glass Fiber-Reinforced Composites. Research Report, Composites Volume 26 Number 10, Elsevier Science Limited, U.K.
  6. Sun W. and Tzeng J. T. 2002. Effective Mechanical Properties of EM Composite Conductors: an Analytical and Finite Element Modeling Approach. Composite Structures. 58: 411-421.
  7. Irfan Sadaq et al., “Characterization and Mechanical Behaviour of Composite Material using FEA”, International Journal of Engineering Research (IJER), ISSN: 2319-6890, 2(2), pp:125-131, 2013
  8. NBV Lakshmi Kumari , S. Irfan Sadaq , G. Prasana Kumar “Analysis of Single Point Cutting Tool of a Lathe Machine Using FEA”, International Journal of Engineering Trends and Technology (IJETT), V20(5),214-217 Feb 2015. ISSN:2231-5381.
  9. Mohd Mohinoddin, S. Irfan Sadaq, Syeda Romana, V. Suvarna Kumar, Experimental characterization of unidirectional carbon – Carbon composite laminate, Materials Today: Proceedings, 2023, ISSN 2214-7853, https://doi.org/10.1016/j.matpr.2023.07.079.
  10. Irfan Sadaq, Syeda Romana, N.B.V. Lakshmi Kumari, G. Prasanna Kumar, S. Shahar Banu, Analysis of optimum stacking sequence of GFRP composite laminate under axial loading condition, Materials Today: Proceedings, Volume 62, Part 6, 2022, Pages 2940-2945, ISSN 2214-7853, https://doi.org/10.1016/j.matpr.2022.02.510.
  11. V. Srividya, Shaik Khadar Vali, B. Hadya, S. Irfan Sadaq, Failure analysis of composite pressure vessel by means of natural and synthetic fibers, Materials Today: Proceedings, 2023, ISSN 2214-7853, https://doi.org/10.1016/j.matpr.2023.07.287.
  12. V. Srividya, Khadar Vali Shaik, B. Hadya, S. Irfan Sadaq; Failure analysis of GFRP and CFRP composite laminated pressure vessel. AIP Conf. Proc.20 February 2024; 3007 (1): 100002. https://doi.org/10.1063/5.0193899
Regular Issue Subscription Review Article
Volume 01
Issue 02
Received March 10, 2024
Accepted March 15, 2024
Published April 25, 2024
Views: 35