Open Access
Umesh Sable
Prashant T. Borlepwar
- P.G. Student Department of Mechanical Engineering, Maharashtra Institute of Technology, Aurangabad Maharashtra India
- Assistant Professor Department of Mechanical Engineering, Maharashtra Institute of Technology, Aurangabad Maharashtra India
Abstract
Additive Manufacturing is one of the non-conventional methods of manufacturing that is gaining immense popularity for its ease to manufacture customized parts. The lenses have always been manufactured using a continuous process of Blanking, Surface generation, Edging and Centering, Grinding, Polishing, and Coating. But the conventional processes demand large inventories and more time. Customization of lenses may also be possible if a process like Additive Manufacturing is implemented. Also, the processes like Blanking, Surface generation, Edging, and Centering can be avoided if they are replaced by only one process i.e. Additive Manufacturing. But whether it is suitable for the manufacturing of lenses is a question of concern. To study its suitability in the current scenario, lenses of three types namely, Plano-Convex, Plano-Concave, and Bi-Convex lens were manufactured using AM process Stereolithography, and test like the Hardness test was conducted. Focal lengths, as well as Radii of Curvature, are measured to check the conformance of the obtained values with the pre- decided values. As a result, due to the unavailability of proper post processing methods, the lenses were found to show low values of hardness and variance of the focal length and curvature values as compared to the conventionally manufactured lenses of similar types.
Keywords: Additive Manufacturing, Stereolithography, Optical lenses, Bi-Convex, Plano-Concave, Plano-Convex.
References
1. Onuh and Yusuf, Rapid prototyping technology: applications and benefits for rapid product development, Journal of Intelligent Manufacturing (1999) 10, 301-311.
2. Jens Bliedtner, production of Optical Plastic Components, Optik and photonic,2017,pp.201-204.
3. John Ryan C. Dizon, Mechanical Characterisation of 3D printed polymers, Additive Manufacturing,2017, 44-67.
4. T. Hanemann, October, Rapid Prototyping and Rapid Tooling Techniques for the Manufacturing of Silicon, Polymer, Metal and Ceramic Micro devices, Research Gate,2007.
5. P.K. Venuvinod, Stereolithography, Rapid Prototyping, Springer Science + Business Media New York,2004.
6. D.T. Pham, Part Orientation in Stereolithography, Int J Adv Manuf Technol (1999),15:674-682.
7. J. M. Dulieu-Barton and M.C. Fulton, Mechanical properties of a Typical Stereo-lithography resin, Strain, 2000,Vol 36, No 2, 81-87.
8. G Beadie, Tunable Polymer lens, OPTICSEXPRESS, 2018, Vol 16, No.167.
9. Katie Schwertz, An introduction to optics manufacturing, OptoMechanics (OPTI521) Report, 2018.
10. Sameen Ahmed Khan, Co-ordinate geometric Generalisation of the Spherometer and cylindrometer,2013, arXiv:1311.3602.
11. Alfonso Costas, Design, Development and characterisation of linear, soft actuators via additive manufacturing, Conference of smart materials, Adaptive systems and Intelligent Systems, 2018, 1-7.
12. Flash print software available at https://www.dream3d.co.uk/product/flashforge-flashprint-3d- printingsoftware/# Overview.
13. http://ncert.nic.in/ncerts/l/lelm308.pdf.
14. Poggio C, Evaluation of Vickers hardness and depth of cure of six composite resins photo-activated with different polymerization modes, Journal of Conservative Dentistry,2019.
15. Quinn, Cracking and Indentation Size Effect for Knoop Hardness of Glasses, Journal of the American Ceramic Society, 2003, Vol 86, Page 442.
16. Elisa Aznarte Garcia, Cagri Ayranci and Jawad Qureshi, Material Property–Manufacturing Process Optimization for Form 2 Vat-Photo Polymerization 3D printers, Journal of Manufacturing and Materials Processing, 2020, 4, page 2.
Trends in Mechanical Engineering & Technology
| Volume | |
| Received | February 3, 2021 |
| Accepted | June 16, 2021 |
| Published | June 16, 2023 |