Open Access
![](http://storage.googleapis.com/journals-stmjournals-com-wp-media-to-gcp-offload/2022/10/vector.jpg)
Mukund Kumar,
![](http://storage.googleapis.com/journals-stmjournals-com-wp-media-to-gcp-offload/2022/10/vector.jpg)
Satish Kumar,
- Research Scholar Department of Mechanical Engineering, National Institute of Technology, Jamshedpur Jharkhand India
- Professor Department of Mechanical Engineering, National Institute of Technology, Jamshedpur Jharkhand India
Abstract
Coatings are utilized for temperature barrier, protection against corrosion and wear etc. Cold spray is a solid-state processing method that is unique among thermal deposition procedures since it deposits particles at temperatures below their melting point. This technology does not involve particle melting, hence retaining the original properties of the materials. Increased coating strength is achieved by retaining of feedstock powder microstructures and characteristics, which prevents oxide formation and other undesirable structural changes. Cold spray is still an emerging, but very promising, technology. In some applications, it offers a way to overcome important limitations of traditional thermal spray technologies, such as high levels of porosity and oxide in the sprayed material. It is well suited for the deposition of oxygen or temperature-sensitive compounds. This process offers a range of technical advantages compared to the thermal spraying method, as it relies on kinetic energy rather than thermal energy. Currently, this process is widely utilized in different sectors to enhance the worth of an item, as it effectively enhances the usability and efficiency of numerous industrial products. When compared to conventional thermal spray processes, cold spray technology is superior at decreasing porosity, increasing hardness, adhesive strength, and retaining characteristics of feedstock powders. This review paper summarizes the cold spray coating technique, focusing on its salient characteristics and practical uses.
Keywords: Cold Spray Coatings, Thermal deposition, Kinetic energy, Hardness, Porosity
[This article belongs to Journal of Polymer and Composites(jopc)]
Browse Figures
References
- Maledi NB, Oladijo OP, Botef I, Ntsoane TP, Madiseng A, Moloisane L. Influence of cold spray parameters on the microstructures and residual stress of Zn coatings sprayed on mild steel. Surface and Coatings Technology. 2017 May 25;318:106-13.
- Gärtner F. Advances in cold spraying. Surface Engineering, 2006; 22(3), 163-169.
- Schmidt T, Assadi H, Gärtner F, Richter H, Stoltenhoff T, Kreye H, Klassen T. From particle acceleration to impact and bonding in cold spraying. Journal of thermal spray technology. 2009 Dec;18:794-808.
- Schmidt T, Gärtner F, Assadi H, Kreye H. Development of a generalized parameter window for cold spray deposition. Acta materialia. 2006 Feb 1;54(3):729-42.
- Papyrin A, Kosarev V, Klinkov S, Alkhimov A, Fomin VM. Cold spray technology. Elsevier; 2006 Oct 4.
- Cavaliere P, Silvello A. Crack repair in aerospace aluminum alloy panels by cold spray. Journal of Thermal Spray Technology. 2017 Apr;26:661-70.
- Pathak S, Saha GC. Development of sustainable cold spray coatings and 3D additive manufacturing components for repair/manufacturing applications: A critical review. Coatings. 2017 Aug 14;7(8):122.
- Da Silva FS, Cinca N, Dosta S, Cano IG, Guilemany JM, Caires CS, Lima AR, Silva CM, Oliveira SL, Caires AR, Benedetti AV. Corrosion resistance and antibacterial properties of copper coating deposited by cold gas spray. Surface and Coatings Technology. 2019 Mar 15;361:292-301.
- Liu Y, Yuan X, Huang H, Wang Y, Lu N, Zhao H, Xiong T. Rapidly solidified Zn-Al powder on surface of Mg alloy by cold spray method. Tezhong Zuzao Ji Youse Hejin(Special Casting & Nonferrous Alloys). 2006(4):204-7.
- Trexler M, Cold spray technology application (ARL, 2010).
- Vilardell AM, Cinca N, Dosta S, Cano IG, Guilemany JM. Feasibility of using low pressure cold gas spray for the spraying of thick ceramic hydroxyapatite coatings. International Journal of Applied Ceramic Technology. 2019 Jan;16(1):221-9.
- Li WY, Li N, Yang XW, Feng Y, Vairis A. Impact of cold spraying on microstructure and mechanical properties of optimized friction stir welded AA2024-T3 joint. Materials Science and Engineering: A. 2017 Aug 15;702:73-80.
- Li WY, Li N, Yang XW, Feng Y, Vairis A. Impact of cold spraying on microstructure and mechanical properties of optimized friction stir welded AA2024-T3 joint. Materials Science and Engineering: A. 2017 Aug 15;702:73-80.
- Santos da Silva F, Cinca i Luis N, Dosta Parras S, García Cano I, Guilemany JM, Benedetti AV. Cold gas spray coatings: basic principles, corrosion protection and applications. Eclética Química Journal, 2017, vol. 42, num. 1, p. 9-32. 2017 Dec 30.
- Fauchais P, Montavon G, Bertrand G. From powders to thermally sprayed coatings. Journal of thermal spray technology. 2010 Jan;19:56-80.
- Rokni MR, Nutt SR, Widener CA, Champagne VK, Hrabe RH. Review of relationship between particle deformation, coating microstructure, and properties in high-pressure cold spray. Journal of thermal spray technology. 2017 Aug;26:1308-55.
- Tazegul O, Dylmishi V, Cimenoglu H. Copper matrix composite coatings produced by cold spraying process for electrical applications. Archives of Civil and Mechanical Engineering. 2016 May 1;16(3):344-50.
- Kumar R, Singh R, Kumar S. Erosion and hot corrosion phenomena in thermal power plant and their preventive methods: a study. Asian Journal of Mechanical Engineering. 2018;7(1):38-45.
- Partovi-Nia R, Ramamurthy S, Zagidulin D, Chen J, Jacklin R, Keech P, Shoesmith DW. Corrosion of cold spray deposited copper coating on steel substrates. Corrosion. 2015 Oct 1;71(10):1237-47.
- Chavan NM, Kiran B, Jyothirmayi A, Phani PS, Sundararajan G. The corrosion behavior of cold sprayed zinc coatings on mild steel substrate. Journal of thermal spray technology. 2013 Apr;22:463-70.
- Spencer K, Zhang MX. Optimisation of stainless steel cold spray coatings using mixed particle size distributions. Surface and Coatings Technology. 2011 Aug 25;205(21-22):5135-40.
- Zhou X, Mohanty P. Electrochemical behavior of cold sprayed hydroxyapatite/titanium composite in Hanks’ solution. Electrochimica Acta. 2012 Mar 30;65:134-40.
- Cinca N, Barbosa M, Dosta S, Guilemany JM. Study of Ti deposition onto Al alloy by cold gas spraying. Surface and Coatings Technology. 2010 Nov 15;205(4):1096-102.
- Choudhuri A, Mohanty PS, Karthikeyan J. Bio-ceramic composite coatings by cold spray technology. InThermal Spray 2009. Proc. Int. Thermal Spray Conf 2009 May 4. Japan Association for Earthquake Engineering.
- Kear G, Barker BD, Stokes K, Walsh FC. Electrochemical corrosion behaviour of 90—10 Cu—Ni alloy in chloride-based electrolytes. Journal of Applied Electrochemistry. 2004 Jul;34:659-69.
- Moridi A, Hassani-Gangaraj SM, Guagliano M, Dao M. Cold spray coating: review of material systems and future perspectives. Surface Engineering. 2014 Jun;30(6):369-95.
- Champagne VK. Repair of magnesium components by cold spray techniques. InThe Cold Spray Materials Deposition Process 2007 Jan 1 (pp. 327-352). Woodhead Publishing.
- Kim J, Kim S, Kim JH. Coating properties of WC-Ni cold spray coating for the application in secondary piping system of nuclear power plants. InProceedings of the KNS 2015 Fall Meeting 2015 Oct 1 (Vol. 47, No. 2015, pp. 1-10).
- Koivuluoto H, Lagerbom J, Vuoristo P. Microstructural studies of cold sprayed copper, nickel, and nickel-30% copper coatings. Journal of Thermal Spray Technology. 2007 Dec;16:488-97.
- Champagne V, Helfritch D. Critical Assessment 11: Structural repairs by cold spray. Materials Science and Technology. 2015 Apr;31(6):627-34.
- Peat T, Galloway A, Toumpis A, Steel R, Zhu W, Iqbal N. Enhanced erosion performance of cold spray co-deposited AISI316 MMCs modified by friction stir processing. Materials & Design. 2017 Apr 15;120:22-35.
- Oliveira AB, Bastos AC, Fernandes CM, Pinho CM, Senos AM, Soares E, Sacramento J, Zheludkevich ML, Ferreira MG. Corrosion behaviour of WC-10% AISI 304 cemented carbides. Corrosion Science. 2015 Nov 1;100:322-31.
- Da Silva FS, Bedoya J, Dosta S, Cinca N, Cano IG, Guilemany JM, Benedetti AV. Corrosion characteristics of cold gas spray coatings of reinforced aluminum deposited onto carbon steel. Corrosion Science, 2017; 114, 57-71.
- Sun C, Guo L, Lu G, Lv Y, Ye F. Interface bonding between particle and substrate during HVOF spraying. Applied surface science. 2014 Oct 30;317:908-13.
- Dosta S, Couto M, Guilemany JM. Cold spray deposition of a WC-25Co cermet onto Al7075-T6 and carbon steel substrates. Acta Materialia. 2013 Jan 1;61(2):643-52.
- Vilardell AM, Cinca N, Cano IG, Concustell A, Dosta S, Guilemany JM, Estradé S, Ruiz-Caridad A, Peiró F. Dense nanostructured calcium phosphate coating on titanium by cold spray. Journal of the European Ceramic Society. 2017 Apr 1;37(4):1747-55.
- Bakshi SR, Singh V, Balani K, McCartney DG, Seal S, Agarwal A. Carbon nanotube reinforced aluminum composite coating via cold spraying. Surface and Coatings Technology. 2008 Jul 30;202(21):5162-9.
- Lee HY, Yu YH, Lee YC, Hong YP, Ko KH. Cold spray of SiC and Al 2 O 3 with soft metal incorporation: A technical contribution. Journal of thermal spray technology. 2004 Jun;13:184-9.
- Wang Y, Normand B, Mary N, Yu M, Liao H. Effects of ceramic particle size on microstructure and the corrosion behavior of cold sprayed SiCp/Al 5056 composite coatings. Surface and Coatings Technology. 2017 Apr 15;315:314-25.
- Cinca N, Guilemany JM. Thermal spraying of transition metal aluminides: An overview. Intermetallics. 2012 May 1;24:60-72.
- Bush TB, Khalkhali Z, Champagne V, Schmidt DP, Rothstein JP. Optimization of cold spray deposition of high-density polyethylene powders. Journal of Thermal Spray Technology. 2017 Oct;26:1548-64.
- ZUBKOV B, KULESHOV A. RESTORATION OF ALUMINIUM ALLOY STRENGTH PROPERTIES BY COLD SPRAY AFTER CORROSION DAMAGE.
- Diab M, Pang X, Jahed H. The effect of pure aluminum cold spray coating on corrosion and corrosion fatigue of magnesium (3% Al-1% Zn) extrusion. Surface and Coatings Technology. 2017 Jan 15;309:423-35.
- Alidokht SA, Vo P, Yue S, Chromik RR. Erosive wear behavior of Cold-Sprayed Ni-WC composite coating. Wear. 2017 Apr 15;376:566-77.
- Seraj RA, Abdollah-zadeh A, Dosta S, Assadi H, Cano IG. Comparison of Stellite coatings on low carbon steel produced by CGS and HVOF spraying. Surface and Coatings Technology. 2019 Aug 25;372:299-311.
![](http://storage.googleapis.com/journals-stmjournals-com-wp-media-to-gcp-offload/2022/12/af025f00-jopc.jpg)
Journal of Polymer and Composites
Volume | 12 |
Issue | 03 |
Received | March 21, 2024 |
Accepted | May 31, 2024 |
Published | July 10, 2024 |