Parametric optimization of COF of fabricated AA6082/Si3N4/C/Al2O3 composite

Open Access

Year : 2024 | Volume : | : | Page : –
By

Dhananjay Kumar

Yashpal

Ratnesh Kumar Sharma

  1. Research Scholar 1Mechanical Engineering Department, Poornima University, Jaipur Rajasthan India
  2. Associate Professor 1Mechanical Engineering Department, Poornima University, Jaipur Rajasthan India
  3. Associate Professor 1Department of Mechanical Engineering, Poornima College of Engineering, Jaipur Rajasthan India

Abstract

In the present experimental investigation AA6082/Si3N4/C/Al2O3 composite was successfully fabri-cated using stir casting technique combined with electromagnetic stirrer for wear resistance applica-tions. The produced AA6082/Si3N4/C/Al2O3 composite exhibits improved tribological and me-chanical and properties, according to the experimental results. The generated composite has a micro-hardness range of 60 to 110 HV and an average UTS of 150 to 200 MPa. The tribological perfor-mance was evaluated using a pin on disc tribometer. The tribometer yields a COF reading be-tween 0.15 and 0.4 for test circumstances of load between 10N and 30N, temperature between 50oC and 100oC, and sliding velocity between 0.1 m/s and 0.3 m/s, respectively. Taguchi L9 OA was also used in the present investigation for optimization of COF of fabricated AA6082/Si3N4/C/Al2O3 compo-site. The percentage contribution of fabricated composite for COF was highest for velocity (76.37%) followed by 12.84 % temperature and 7.31 % load. The following are the predicted ideal values for the 95% confidence interval for COF for the fabricated AA6082/Si3N4/C/Al2O3 composite. 0.86 µ < 0.134 for CICE and CIPOP: µ < 0.0126 < 0.094

Keywords: AA6082/Si3N4/C/Al2O3 composite; SEM-EDAX; COF; Taguchi.

How to cite this article: Dhananjay Kumar, Yashpal, Ratnesh Kumar Sharma. Parametric optimization of COF of fabricated AA6082/Si3N4/C/Al2O3 composite. Journal of Polymer and Composites. 2024; ():-.
How to cite this URL: Dhananjay Kumar, Yashpal, Ratnesh Kumar Sharma. Parametric optimization of COF of fabricated AA6082/Si3N4/C/Al2O3 composite. Journal of Polymer and Composites. 2024; ():-. Available from: https://journals.stmjournals.com/jopc/article=2024/view=0

Full Text PDF Download

References

  1. Nevshupa, M. Conte, A. del Campo, E. Roman, Analysis of tribochemical decomposition of two imidazolium ionic liquids on Ti–6Al–4V through Mechanically Stimulated Gas Emission Spectrometry, Tribol Int 102 (2016) 19–27.
  2. J. Profito, E. Tomanik, D.C. Zachariadis, Effect of cylinder liner wear on the mixed lubrication regime of TLOCRs, Tribol Int 93 (2016) 723–732.
  3. B. Zavos, P.G. Nikolakopoulos, Simulation of piston ring tribology with surface texturing for internal combustion engines, Lubr Sci 27 (2015) 151–176.
  4. Igartua, R. Nevshupa, X. Fernandez, M. Conte, R. Zabala, J. Bernaola, Alternative eco-friendly lubes for clean two-stroke engines, Tribol Int 44 (2011) 727–736.
  5. Ankit Tyagi, Deepak Sharma, 2018, “Characterization of AA6082/Si3N4 Composites”, 1st International Conference on New Frontiers in Engineering, Science & Technology, 231-237, ISBN: 978-93-86238-41-2
  6. Ajit Kumar Senapati, R. I. Ganguly, R.R. Dash, P.C. Mishra, B. C. Routra, Production, characterization and analysis of mechanical properties of newly developed novel aluminium silicon alloy based metal matrix composited, Procedia Materials Science 5 (2014) 472-481.
  7. Pardeep Sharma, Dinesh Khanduja, Satpal Sharma, Parametic study of dry sliding wear of aluminium metal matrix composites by response surface methodology, Materials Today: Proceeding 2 (2015) 2687-2697.
  8. Manoj Singla, D Deepak Dwivedi, Lakhvir Singh, Vikas Chawla, Development of Aluminium Based Silicon Carbide Particulate Metal Matrix Composite, Journal of Minerals & Materials Characterization & Engineering 8 (2009) 455-467.
  9. Ankit Tyagi, Yashwant koli, 2017, “Crictical Review of Fabrication & Characterization of Metal Matrix Composites”, International Journal on Future Revolution in Computer Science & Communication Engineering, Vol. 3, Issue, 11, pp. 68-73, ISSN: 2454-4248.
  10. Ashok K.R. Mishra, Ravindra Yadav, R.K. Srivastava, Eur. J. Sci. Res. 98 (2013) 542–550. ISSN 1450-216X / 1450-202X
  11. Ravi Yadav, Ravindra Yadav, Ashok K.R. Mishra, et al., Tribological Behaviour of Al6061/Al2O3/Flyash Metal, in: Matrix Composite, National conference on Advances in mechanical Engineering, 2014, pp. 301–307.
  12. Md Abdul Maleque, Md Rezaul Karim, Tribological behavior of dual and triple particle size SiC reinforced Al-MMCs: a comparative study, Indus. Lubric. Tribol. 60(4) (2012) 189–194.
  13. Ravi Kumar et al., Influence of particle size on dry sliding friction and wear behavior of fly ash particle reinforced A380 Al matrix composites, Eur. J. Sci. Res. 60 (3) (2011) 410–420.
  14. Ankit Tyagi, R.S. Walia, Qasim Murtaza, “Tribological behavior of temperature dependent environment friendly thermal CVD diamond coating”, Diamond & Related Materials 96 (2019) 148–159.
  15. Ankit Tyagi, Yashwant koli, Deepak Sharma, 2018, “Fabrication & mechanical testing of AA6082/Si3N4 Composites”, International Journal of Scientific Research in Science and Technology, Vol. 4, Issue 2, pp. 579-582, ISSN: 2395-6011 (Print), Online ISSN: 2395-602X.
  16. Ashok, N. Murugan, Metallurgical and mechanical characterization of stir cast AA6061-T6- AlNp composite, Materials and Design 40 (2012) 52- 58.
  17. I Dinaharan, N Murugan, S Parameswaran, Influence of in situ formed ZrB2particles on microstructure and mechanical properties of AA6061 metal matrix composites, Mater Sci Eng A 528 (2011) 5733–40.
  18. S. Ramesh, R. Keshavamurthy, B.H. Channabasappa, S. Pramod, Friction and wear behaviour of Ni-P coated Si3N4 reinforced Al6061 composites, Tribology International 43 (2010) 623−634.
  19. Arik, Effect of mechanical alloying process on mechanical properties of _-Si3N4 reinforced aluminium-based composite materials, Materials and Design 29 (2008) 1856−1861.
  20. Ankit Tyagi, Shailesh Mani Pandey, R.S. Walia, Qasim Murtaza, “Characterization and parametric optimization of tribological properties of Mo blend composite coating”, Material research express, Mater. Res. Express 6 (2019) 086428
  21. Ankit Tyagi, SM Pandey, Qasim Murtaza, R.S. Walia, Mohit Tyagi, “Tribological behavior of carbon coating for piston ring applications using Taguchi approach”, Materials today proceeding 25 (2020) 759–764.
  22. Ankit Tyagi, S M Pandey, R S Walia, Qasim Murtaza, “Characterization and parametric optimization of % change in residual stress of Mo composite coating using Taguchi approach” Materials Research Express,  (Accepted).
  23. Ankit Tyagi, R S Walia, Qasim Murtaza, “Tribological behavior of HVOF carbon coating for wear resistance applications” Materials Research Express, Volume 6, Number 12.
  24. Ankit Tyagi, S M Pandey, R S Walia, Qasim Murtaza, “Characterization and parametric optimization of % change in residual stress of Mo composite coating using Taguchi approach” Materials Research Express,  6 (2019) 125623
  25. Ankit Tyagi, R S Walia, Qasim Murtaza, “Residual, Corrosion & Tribological behavior of HVOF sprayed sustainable temperature dependent carbon based hybrid composite coating”, Strojniški vestnik – Journal of Mechanical Engineering, 67(2021)4, 191-199.
  26. Ankit Tyagi, SM Pandey, Qasim Murtaza, R.S. Walia, “Effect of temperature on the sliding wear behavior of HVOF sprayed Al2O3 composite coating”, Advances in Materials and Mechanical Engineering, Lecture Notes in Mechanical engineering, ISBN 978-981-16-0673-1.
Ahead of Print Open Access Original Research
Volume
Received January 23, 2024
Accepted March 6, 2024
Published May 17, 2024
Views: 23

function myFunction2() {
var x = document.getElementById(“browsefigure”);
if (x.style.display === “block”) {
x.style.display = “none”;
}
else { x.style.display = “Block”; }
}
document.querySelector(“.prevBtn”).addEventListener(“click”, () => {
changeSlides(-1);
});
document.querySelector(“.nextBtn”).addEventListener(“click”, () => {
changeSlides(1);
});
var slideIndex = 1;
showSlides(slideIndex);
function changeSlides(n) {
showSlides((slideIndex += n));
}
function currentSlide(n) {
showSlides((slideIndex = n));
}
function showSlides(n) {
var i;
var slides = document.getElementsByClassName(“Slide”);
var dots = document.getElementsByClassName(“Navdot”);
if (n > slides.length) { slideIndex = 1; }
if (n (item.style.display = “none”));
Array.from(dots).forEach(
item => (item.className = item.className.replace(” selected”, “”))
);
slides[slideIndex – 1].style.display = “block”;
dots[slideIndex – 1].className += ” selected”;
}